Kawasaki Vulcan 2000 VN2000 Service & Repair Manual
A workshop, service or technical manual for the stated model. Coverage is limited to what the original technical index supports; a full independent wiring-diagram collection is not implied by ordinary electrical-system chapters.
Indexed technical areas: engine and mechanical systems, gearbox and transmission, braking and steering systems, suspension and axles, electrical components and circuits.
Examples from the original contents: General Information; Oxygen Sensor Removal/Installation; Oil Pressure Gauge, 5 kg/cm² : 57001–125; Oil Seal & Bearing Remover : 57001–1058.
Important document scope / limitation: The listed electrical coverage includes an indexed DFI wiring diagram, but a complete independent circuit-diagram set is not established.
Original technical index
- CONTENTS:
- Foreword
- General Information
- - Before starting-perform an inspection service or carry out a
- - VN2000-A1 (US, and Canada) Left Side View:
- - VN2000-A1 (US, and Canada) Right Side View:
- - VN2000-A1 (Europe) Left Side View:
- - VN2000-A1 (Europe) Right Side View:
- - Overview
- - An automatic decompressor (Automatic Compression Reliese) system
- - Dual balancers harmonize primary balance and reduce vibration.
- - Prefixes for Units:
- - Units of Temperature:
- Periodic Maintenance
- - The scheduled maintenance must be done in accordance with this c
- - The following tables list the tightening torque for the major fa
- - Inside Circlip Pliers: 57001–143
- - Steering Stem Nut Wrench: 57001–1100
- - Jack: 57001–1238
- - Oil Filter Wrench: 57001–1249
- - Spark Plug Wrench, Hex 16: 57001–1262
- - Jack Attachment : 57001–1571
- - Drive Belt Tension Gauge: 57001– 1585
- - Steering System:
- Fuel System (DFI)
- - Oil Pressure Gauge, 5 kg/cm² : 57001–125
- - Fork Oil Level Gauge : 570101–1290
- - Hand Tester : 57001–1394
- - Fuel Pressure Gauge Adapter : 57001–1593
- - Needle Adapter Set : 57001–1457
- - Kawasaki Bond (Silicone Sealant) : 56019–120
- - Throttle Sensor Setting Adapter: 57001–1400
- - Fuel Hoses: 57001–1607
- - DFI System Wiring Diagram
- - There are a number of important precautions that should be follo
- - Outline
- - NOTE
- - Self-diagnosis Outline
- - The main throttle sensor is a rotating variable resistor that ch
- - Removal
- - Removal/Installation
- - Removal/Installation
- - Removal
- - Start the engine and switch the diagnosis mode-Dealer 1 mode
- - Camshaft Position Sensor Removal/Installation
- - Speed Sensor Removal/Installation
- - Gear Position Switch Removal/Installation
- - Vehicle-down Sensor Removal
- - The subthrottle sensor is a rotating variable resistor that chan
- - Oxygen Sensor Removal/Installation
- - Fuel Injector ##1: Front Fuel Injector for Front Cylinder (Servic
- - Fuel Pump Removal
- - Ignition Coil ##1: Ignition Coil for Front Cylinder (Service Code
- - Starter Control Relay Removal and Installation
- - Radiator Fan Relay Removal/Installation
- - Subthrottle Valve Actuator Removal
- - Air Switching Valve Removal/Instalation
- - Decompression Solenoid Removal/Installation
- - Oxygen Sensor Heater Removal/Installation
- - Subthrottle Motor Driver Removal/Installation
- - Oxygen Sensor Removal/Installation
- - Inspection Flow Chart
- - ECU Removal
- - Fuel Pressure Inspection
- - Throttle Grip Free Play Inspection
- - Idle Speed Check
- - Element Removal
- - Fuel Tank Removal
- - The Evaporative Emission Control System for California Model rou
- Cooling System
- - Permanent type antifreeze is used as a coolant-protect the co
- - Bearing Driver Set : 57001–1129
- - Bearing Remover Shaft : 57001–1265
- - Bearing Remover Head, ϕ10 x ϕ12 : 57001–1266
- - Coolant Deterioration Inspection
- - Water Pump Removal
- - WARNING
- - Thermostat Removal
- - Hose Installation
- Engine Top End
- - Cam Height
- - Push Rod Length and Runout
- - Valve Head Thickness
- - Valve Stem Bend
- - Camshaft Journals
- - Valve Guide Reamer, ϕ6 : 57001–1596
- - Valve Guide Arbor, ϕ5.7 : 57001–1564
- - Compression Gauge : 57001–221
- - Valve Spring Compressor Assembly : 57001–241
- - Valve Spring Compressor Adapter, ϕ28.2 : 57001–243
- - Compression Gauge Adapter, M14 x 1.25 : 57001–1590
- - Spark Plug Wrench, Hex 16 : 57001–1262
- - Piston Ring Compressor Grip : 57001–1095
- - Valve Seat Cutter, 45° – ϕ41.5 : 57001–1117
- - Valve Seat Cutter, 32° – ϕ38.5 : 57001–1122
- - Valve Seat Cutter, 60° – ϕ41 : 57001–1124
- - Valve Seat Cutter Holder, ϕ6 : 57001–1576
- - Valve Seat Cutter Holder Bar : 57001–1128
- - Piston Ring Compressor Belt, ϕ95 ~ ϕ108 : 57001–1358
- - Valve Seat Cutter 45° – ϕ40 : 57001–1496
- - Valve Seat Cutter 32° – ϕ44 : 57001–1515
- - Piston Pin Puller Assembly: 57001–1568
- - Bearing Driver Set: 57001–1129
- - Air Suction Valve Removal
- - Rocker Case Cover Removal
- - Rocker Case Removal
- - Decompression Mechanism Removal
- - Camshaft Removal
- - Cylinder Compression Measurement
- - Cylinder Removal
- - Upper Muffler Removal
- Clutch
- - Clutch Holder: 57001–1243
- - Flywheel & Pulley Holder: 57001–1343
- - Flywheel & Pulley Holder Adapter: 57001–1547
- - Kawasaki Bond (Liquid Gasket-Black): 92104–1064
- - Lever Free Play Inspection
- - Outer Clutch Cover Removal
- Engine Lubrication System
- - Oil Pressure Gauge, 5 kg/cm² : 57001–125
- - Oil Pressure Gauge Adapter, PT 1/8 : 57001–1033
- - Oil Filter Wrench : 57001–1249
- - Kawasaki Bond (Silicone Sealant) : 56019–120
- - Because of the semi-dry sump lubrication system, the engine oil
- - Oil Pump Removal
- - Oil Pan Removal
- - Oil Pressure Measurement
- Engine Removal/Installation
- - Jack : 57001–1238
- - Socket Wrench: 57001–1347
- - Jack Attachment: 57001–1571
- - Engine Removal
- Crankshaft/Transmission
- - Outside Circlip Pliers : 57001–144
- - Gear Holder : 57001–1574
- - Bearing Driver Set : 57001–1129
- - Flywheel & Pulley Holder : 57001–1343
- - Kawasaki Bond (Liquid Gasket – Black) : 92104–1064
- - Flywheel & Pulley Holder Adapter 57001–1547
- - Crankcase Disassembly
- - Connecting Rod Removal
- - Balancer Mechanism Removal
- - Shift Pedal Removal
- - Ball Bearing and Outer Race Replacement
- Wheels/Tires
- - Inside Circlip Pliers : 57001–143
- - Bearing Driver Set : 57001–1129
- - Jack : 57001–1238
- - Bearing Remover Head, 20 x 22 : 57001–1293
- - Bearing Remover Head, 25 x 28 : 57001–1346
- - Bearing Remover Shaft, 13 : 57001–1377
- - Jack Attachment : 57001–1571
- - Front Wheel Removal
- - Air Pressure Inspection/Adjustment
- - Hub Bearings Removal
- Final Drive
- - Inside Circlip Priers : 57001–143
- - Oil Seal & Bearing Remover: 57001–1058
- - Bearing Driver Set : 57001–1129
- - Pulley Holder : 57001–1572
- - Grip : 57001–1591
- - The drive belt must be checked, and adjusted in accordance with
- - Engine Pulley Cover Removal
- Brakes
- - Inside Circlip Pliers: 57001–143
- - Brake Lever Position Adjustment
- - Front Caliper Removal
- - Front Brake Pad Removal
- - Front Master Cylinder Removal
- - Brake Disc Removal
- - Brake Fluid Level Inspection
- - Brake Hose Removal/Installation
- Suspension
- - Inside Circlip Pliers: 57001–143
- - Fork Cylinder Holder Handle : 57001–183
- - Fork Cylinder Holder Adapter : 57001–1057
- - Oil Seal & Bearing Remover : 57001–1058
- - Bearing Driver Set : 57001–1129
- - Jack : 57001–1238
- - Fork Oil Level Gauge : 570101–1290
- - Jack Attachment : 57001–1571
- - Hook Wrench : 57001–1580
- - Fork Oil Seal Driver, 49 : 57001–1589
- - Fork Oil Change
- - Rebound Damping Force Adjustment
- - Swingarm Removal
- Steering
- - Head Pipe Outer Race Press Shaft : 57001–1075
- - Head Pipe Outer Race Driver : 57001–1077
- - Head Pipe Outer Race Remover : 57001–1107
- - Steering Stem Nut Wrench : 57001–1100
- - Steering Stem Bearing Driver : 57001–1344
- - Steering Stem Bearing Driver Adapter : 57001–1345
- - Handlebar Removal
- - Steering Check
- - Steering Stem Removal
- - Stem Bearing Removal
- Frame
- - Jack: 57001–1238
- - Jack Attachment: 57001–1571
- - Rear Seat Removal
- - Right Side Cover Removal
- - Front Fender Removal
- - Tool Case Removal
- - Right Footboard Removal
- - Downtube Removal
- - Headlight Cover Removal
- - Frame Inspection
- Electrical System
- - Spark Plug Wrench, Hex 16 : 57001–1262
- - Jack : 57001–1238
- - Hand Tester : 57001–1394
- - Flywheel & Pulley Holder: 57001–1343
- - Filler Cap Driver : 57001–1454
- - Needle Adapter Set: 57001–1457
- - Flywheel & Pulley Holder Adapter: 57001–1547
- - Jack Attachment : 57001–1571
- - Left Handlebar Switches [A]
- - There are a number of important precautions that should be follo
- - Wiring Inspection
- - Battery Removal
- - Alternator Rotor Removal
- - Starter Motor Removal
- - This model adopts the daylight system and has a headlight relay
- - Automobiles use a turn signal canceling system actuated by steer
- - Fan Motor Inspection
- - Meter Unit Removal
- - Air Switching Valve Operation Test
- - Decompression Solenoid Inspection
- - Fuel Level Sensor Inspection
- - The relay box [A] has relays and diodes. The relays and diodes c
- - Main Fuse Removal
- Appendix
- - NOTE