• -$10.00
BMW K 1200 LT - Service Manual - Manual de Taller
search
  • BMW K 1200 LT - Service Manual - Manual de Taller

BMW K 1200 LT - Service Manual - Manual de Taller

$29.95
$19.95 Save $10.00
No tax
Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

BMW K 1200 LT - Service Manual - Manual de Taller

Digital technical documentation with sections on REPAIR MANUAL, MAINTENANCE SCHEDULE, 00 MAINTENANCE AND GENERAL INSTRUCTIONS. Review the complete contents below for the systems and procedures covered.

Manual contents

  • REPAIR MANUAL
  • INTRODUCTION
  • Usage
  • Key-symbols
  • Contents
  • Activities
  • CONTENTS
  • MAINTENANCE SCHEDULE
  • PRE-DELIVERY CHECK
  • 00 MAINTENANCE AND GENERAL INSTRUCTIONS
  • Tightening torques
  • Table of operating fluids
  • Overview: K1200LT packing materials
  • Checking the shipping crate for damage
  • Damage discovered in Germany
  • Damage discovered in importer markets
  • Unpacking the motorcycle
  • Installing the front wheel
  • General instructions
  • Pushing the motorcycle onto a workshop platform
  • Inspecting motorcycle for damage
  • Checking that delivery is complete
  • Installing remaining items on motorcycle
  • Installing the front mudguard
  • Installing the mirrors
  • Installing the footrests
  • Installing the rear left footrest plate
  • Installing the rear right footrest and footrest pl...
  • Installing the engine spoilers
  • Installing the reverser control
  • Installing the skirts
  • Installing the top case
  • Additional instructions for moving the backrest
  • Filling and charging the battery
  • Checking brake fluid level
  • Front brake
  • Rear brake
  • Checking clutch fluid level
  • Checking tyre pressures
  • Checking tightness of rear wheel studs
  • Installing the aerial
  • Installing the windscreen
  • Installing the windscreen cover
  • Checking and adjusting the motorcycle
  • Checking the function of side stand contact switch...
  • Adjusting the seat
  • Adjusting the top case
  • Checking headlight beam angle, adjusting if necess...
  • Vertical adjustment
  • Lateral adjustment
  • Final inspection and function check
  • Final cleaning
  • Key-maintenance intervals
  • General instructions
  • Pushing the motorcycle onto a workshop platform
  • High idle speed
  • Removing the aerial
  • Reading the fault code memory with the MoDiTeC
  • (Inspections I, II, III and IV)
  • Checking throttle cable play, adjusting if necess...
  • (Inspections I and III)
  • Models without cruise control
  • Models with cruise control
  • Throttle-opener cable, throttle-closer cable
  • Cruise-control system cable
  • Turning the throttle twist grip relative-the th...
  • Cruise control system does not switch off
  • Cruise control system cannot be set, or continuall...
  • Changing engine oil, replacing oil filter element
  • (Inspections I, II, III and IV)
  • Changing gearbox oil
  • Change the gearbox oil every two years at the late...
  • (Inspection III)
  • Changing the oil in the rear wheel drive
  • Change the oil in the rear wheel drive every two y...
  • (Inspections I and III)
  • Brake pads/brake discs
  • Checking brake pads and discs for wear and replaci...
  • (Inspections II and III)
  • Checking brake pads for wear
  • Front brake pads
  • Rear brake pads
  • Replacing brake pads
  • Front brake
  • Rear brake
  • Checking the brake discs
  • Checking the front/rear brake fluid level
  • (Inspections I, II and III)
  • Checking the front brake fluid level
  • Checking the fluid level with brake fluid reservoi...
  • Checking the rear brake fluid level
  • (Inspections I, II and III)
  • Checking operation of brake system and freedom fro...
  • (Inspection III)
  • Changing brake fluid and bleeding brake system
  • Change the brake fluid once a year at the latest
  • (Inspection IV)
  • Front brake
  • Forcing back the brake pistons
  • Opening the brake fluid reservoir
  • Bleeding the front brake pressure modulator
  • Bleeding the left brake calliper
  • Bleeding the front right brake calliper
  • Rear brake
  • Bleeding the rear brake pressure modulator
  • Forcing back the brake pistons
  • Bleeding the brake calliper
  • Checking clutch fluid level
  • (Inspections I, II and III)
  • Changing the clutch fluid (every 40, 000 km/24, 00...
  • Change the clutch fluid every 2 years at the lates...
  • (Inspection III)
  • Replacing fuel filter (every 40,000 km/24,000 mile...
  • (Inspection III)
  • Removing the fuel pump unit
  • Removing and installing fuel filter
  • Installing the fuel-pump unit
  • Checking and topping up, if necessary, coolant le...
  • (Inspections I and III)
  • Changing coolant
  • (Inspection IV)
  • Draining coolant
  • Filling coolant system
  • Battery
  • (Inspections III and IV)
  • Check battery acid level and add distilled water i...
  • Checking battery acid level
  • Adding distilled water
  • Installing the battery
  • Replacing intake air filter element
  • (Inspection III)
  • Checking function of side stand contact switch
  • (Inspections I, II and III)
  • Greasing the side stand
  • (Inspections II, III and IV)
  • Checking the centre stand, greasing if necessary
  • (Inspections II, III and IV)
  • Checking the centre stand
  • Greasing the centre stand
  • Checking the steering damper
  • (Inspections II and III)
  • Checking tightness of rear wheel studs
  • (Inspection I)
  • Checking rear wheel bearing play by tilting wheel
  • (Inspection III)
  • Checking swinging arm bearings, adjusting if neces...
  • (Inspections I and III)
  • Cleaning the inductive sensor on the rear wheel (e...
  • Clean the inductive sensor on the rear wheel every...
  • (Inspection III)
  • Checking valve clearances, adjusting if necessary...
  • (Inspection III)
  • Checking valve clearances
  • Adjusting valve clearances
  • Replacing the chain tensioning rail lining and cha...
  • (every 60,000 km/36,000 miles)
  • Replacing spark plugs
  • (Inspection III)
  • Final inspection with road safety and functional c...
  • (Inspections I, II, III and IV)
  • 11 MOTOR
  • Cutaway drawing of engine, K 1200 LT
  • Preparatory work with engine installed
  • …for removal of combined oil/water pump
  • …for removal of timing case cover, removal of timi...
  • ...for removal of cylinder head
  • Removing/installing engine
  • Removing engine
  • Group: frame
  • Groups: radiators, fuel tank and fuel lines
  • Group: exhaust system
  • Groups: rear-wheel drive, wheels and tyres
  • Groups: frame and clutch
  • Groups: engine electrical system and general vehic...
  • Group: frame and gearbox
  • Installing engine
  • Groups: frame and gearbox
  • Group: clutch
  • Groups: engine electrical system and general vehic...
  • Groups: frame, rear-wheel drive, wheels and tyres
  • Group: exhaust system
  • Groups: radiators, fuel tank and fuel lines
  • Group: frame
  • Disassembling engine
  • Removing, disassembling/assembling water pump
  • Removing the oil/water pump
  • Disassembling the oil/water pump
  • Removing slipring seal and shaft sealing ring
  • Removing the oil pressure relief valve
  • Installing the oil pressure relief valve
  • Oil-pressure switch, temperature sensor for water ...
  • Installing the pump shaft with shaft sealing ring ...
  • Installing water pump impeller
  • Removing timing chain cover
  • Removing cylinder head cover
  • Removing ignition pulse generator
  • Removing timing chain cover
  • Removing/installing sealing ring in timing case co...
  • Removing the timing chain
  • Removing camshaft chain sprockets
  • Removing chain tensioner rail
  • Removing chain guide rail
  • Renewing tensioning strap for chain tensioner rail...
  • Removing, disassembling and assembling cylinder h...
  • Removing camshafts
  • Removing bucket-type tappets
  • Removing cylinder head
  • Removing valves
  • Machining valve seat
  • Installing valve and valve stem seal
  • Removing/installing crankshaft gear and rotor flan...
  • Removing crankshaft
  • Removing big end bearings
  • Removing main bearings (engine installed)
  • Removing main bearings (engine removed)
  • Removing, disassembling and assembling piston with...
  • Removing piston with conrod
  • Disassembling piston
  • Checking piston dimensions
  • Assembling pistons
  • Checking cylinder dimensions
  • Checking that conrod bores are parallel
  • Assembling pistons and conrods
  • Measure backlash at the countershaft
  • Removing intermediate flange
  • Removing driver
  • Removing clutch housing
  • Removing intermediate flange
  • Disassembling/assembling intermediate flange
  • Removing the driver bearing
  • Installing driver bearing
  • Removing/installing shaft sealing ring for driver
  • Removing countershaft and layshaft with freewheel
  • Disassembling/assembling freewheel
  • Disassembling freewheel
  • Assembling freewheel
  • Removing/installing needle bearing for layshaft an...
  • Removing bearing
  • Removing shaft sealing ring
  • Installing shaft sealing ring
  • Installing bearing
  • Removing output shaft
  • Removing oil sump
  • Removing the oil mesh strainer and oil filter
  • Removing lower part of crankcase
  • Removing/installing oil level sight glass
  • Disassembling/reassembling output shaft
  • Disassembling output shaft
  • Disassembling tensioning gear
  • Assembling tensioning gear
  • Assembling damper
  • Assembling engine
  • Installing output shaft
  • Assembling the crankcase
  • Installing oil mesh strainer
  • Installing oil filter
  • Installing oil sump
  • Installing intermediate flange
  • Installing freewheel
  • Installing countershaft
  • Installing intermediate flange
  • Installing output shaft sealing ring
  • Installing clutch housing
  • Installing driver
  • Installing crankshaft
  • Measuring crankshaft bearing play
  • Measuring radial play
  • Measuring endplay
  • Installing piston with conrod
  • Installing big end bearing
  • Measuring big end bearing play
  • Checking dimensions of crankshaft
  • Installing cylinder head
  • Installing camshafts
  • Installing timing chain
  • Installing timing case cover
  • Checking valve clearances
  • Adjusting valve clearances
  • Installing ignition pulse generator
  • Installing ignition pulse generator cover
  • Installing combined oil/water pump
  • Installing crankcase cover
  • Installing cylinder head cover
  • 12 ENGINE ELECTRICS
  • Removing and installing Hall-effect transmitters
  • Preparatory work
  • Removing cover from Hall-effect transmitter
  • Removing magnetic gate
  • Installing the magnetic gate
  • Installing the cover of the Hall-effect transmitte...
  • Replacing spark plugs/ignition leads
  • Removing and installing spark plugs
  • Removing and installing ignition leads
  • Removing and installing coil
  • Motorcycles without shield housing
  • Motorcycles with shield housing
  • Timing the ignition
  • Preparatory work
  • Setting timing with Motronic
  • Setting timing without Motronic
  • Replacing three-phase generator
  • Removing and installing three-phase generator
  • Disassembling the three-phase generator
  • Removing and installing drive housing
  • Removing and installing voltage regulator
  • Replacing starter motor
  • Removing and installing starter motor
  • Disassembling/assembling starter motor
  • Replacing carbon brushes
  • 13 FUEL PREPARATION AND CONTROL
  • Removing and installing Motronic control unit
  • Replacing intake air filter element
  • See Group 00
  • Replacing air temperature sensor
  • Removing and installing intake air silencer
  • Removing and installing fuel injection rail
  • Removing and installing injectors
  • Removing and installing pressure regulator
  • Removing and installing throttle valve rail
  • Removing and installing throttle valve actuator
  • Replacing and adjusting throttle valve potentiomet...
  • Removing and installing intake stubs
  • Replacing fuel hoses
  • Removing and installing throttle cables
  • Preparatory work for all Bowden cables
  • Removing and installing throttle- opener and throt...
  • Removing and installing Bowden cable of cruise-con...
  • Checking fuel pressure
  • Removing and installing control unit of cruise-con...
  • See Group 65
  • Checking throttle cable play, adjusting if necess...
  • See Group 00
  • 16 FUEL TANK AND LINES
  • Removing and installing fuel tank
  • Renewing fuel filter
  • Removing the fuel pump unit
  • Removing/installing fuel filter
  • Removing/installing fuel pump
  • Installing the fuel-pump unit
  • Removing/installing immersion-tube sensor
  • Calibrating the immersion-tube sensor
  • Removing/installing roll-over valve
  • 17 RADIATOR
  • Coolant circuit
  • Removing and installing coolant hoses
  • Connecting hose between left and right radiators
  • Hoses between radiators and coolant stub pipes
  • Hose between coolant stub pipes
  • Coolant hose-water pump
  • Removing breather hose
  • Vapour outlet hose
  • Changing coolant
  • See Group 00
  • Checking cooling system for leaks
  • Removing and installing radiator with fan
  • Removing and installing left radiator
  • Removing and installing right radiator
  • Removing and installing coolant stub pipe on engin...
  • Removing and installing thermostat
  • Troubleshooting
  • 18 EXHAUST SYSTEM
  • Removing and installing exhaust heat shield
  • Removing and installing exhaust system
  • Removing oxygen sensor
  • 21 CLUTCH
  • Removing and installing clutch
  • Preparatory work
  • Removing clutch
  • Removing clutch housing
  • Installing clutch housing
  • Installing clutch
  • Changing the clutch fluid/bleeding the clutch syst...
  • Removing and installing clutch lines
  • Removing and installing vent line
  • Removing and installing clutch pressure line
  • Removing and installing clutch slave cylinder
  • Removing and installing clutch release rod
  • 23 GEARBOX
  • Gearbox – sectional drawing
  • Replacing the shaft sealing rings in the gearbox h...
  • Replacing input shaft sealing ring at input side
  • Replacing output shaft sealing ring
  • Replacing shaft sealing ring for selector shaft o...
  • Replacing input shaft sealing ring at output side
  • Replacing shaft sealing ring for selector drum
  • Replacing shaft sealing ring for selector shaft
  • Removing and installing actuating unit for reverse...
  • Removing and installing actuating control for reve...
  • Removing and installing actuating unit for reverse...
  • Disassembling/assembling double switch for reverse...
  • Removing gearbox
  • Disassembling gearbox
  • Preparatory work
  • Disassembling reverser gear train
  • Removing gearbox housing
  • Removing selector drum
  • Disassembling/assembling selector shaft
  • Removing gearbox shafts
  • Replacing grooved ball bearing on intermediate sha...
  • Disassembling/assembling input shaft
  • Disassembling input shaft
  • Assembling input shaft
  • Checking travel of spring segment on input shaft
  • Disassembling/assembling output shaft
  • Disassembling output shaft
  • Assembling output shaft
  • Checking endplay
  • Checking/adjusting fully assembled length of gearb...
  • Checking/adjusting fully assembled length of inter...
  • Checking/adjusting fully assembled length of outpu...
  • Checking/adjusting fully assembled length of input...
  • Checking/adjusting fully assembled length of selec...
  • Shimming selector shaft
  • Assembling gearbox
  • Installing gearbox shafts
  • Installing input, output and intermediate shafts
  • Installing selector shaft
  • Installing selector drum
  • Installing gearbox housing
  • Installing reverser
  • Performing a functional check
  • Installing cover of reverser
  • Install actuator unit for reverser
  • Completing assembly of gearbox
  • Installing gearbox
  • Removing and installing gearshift lever and linkag...
  • Removing and installing gearshift lever
  • Aligning rubber mounts
  • Aligning left-hand rubber mount
  • Aligning right-hand rubber mount
  • 31 FRONT FORK
  • Removing and installing telescopic forks and fork ...
  • Removing telescopic fork
  • Removing fork bridge
  • Disassembling fork bridge
  • Removing and installing pot-type joints
  • Removing angular-contact ball bearing with stud
  • Removing stud
  • Installing stud
  • Installing angular-contact ball bearing with stud
  • Installing fork bridge
  • Installing telescopic fork
  • Assembly specification for telescopic fork
  • Disassembling/assembling telescopic fork leg
  • Disassembling telescopic fork leg
  • Assembling telescopic fork leg
  • Measuring telescopic fork
  • Examining slider tube bridge and fork bridge
  • Checking runout of fixed tube
  • Checking runout of slider tube
  • Removing and installing slider tube bridge
  • Removing and installing ball joint
  • Removing and installing front suspension strut
  • Removing front suspension strut
  • Installing suspension strut
  • Removing and installing steering damper
  • Checking the steering damper
  • See Group 00
  • Removing and installing leading link
  • Removing leading link
  • Removing left angular-contact ball bearing for lea...
  • Installing left angular-contact ball bearing for l...
  • Installing leading link
  • Measuring the leading link
  • 32 STEERING
  • Removing and installing left grip tube
  • Removing and installing right grip tube
  • Removing and installing clutch lever fitting
  • Removing and installing brake lever fitting
  • Removing and installing handlebar
  • Installation instructions for adjusting handlebar
  • Handlebar: adjusting horizontally
  • Handlebar: adjusting height
  • Removing and installing piston in brake-lever fitt...
  • Adjusting lever play for front brake/ clutch
  • Front brake
  • Clutch
  • Removing and installing left and right handlebar l...
  • Removing and installing throttle cables
  • See Group 13
  • 33 REAR WHEEL DRIVE
  • Rear wheel drive – cutaway drawing
  • Removing, disassembling, reassembling and install...
  • Removing rear wheel drive
  • Replacing taper roller bearing in rear wheel drive...
  • Removing input bevel pinion
  • Disassembling input bevel pinion
  • Removing needle roller bearing for input bevel pin...
  • Installing needle roller bearing for input bevel p...
  • Assembling input bevel pinion
  • Installing input bevel pinion
  • Removing crown wheel
  • Installing crown wheel
  • Checking/adjusting backlash
  • Checking tooth contact pattern
  • Shimming housing cover
  • Installing housing cover
  • Installing rear drive shaft
  • Installing rear wheel drive
  • Removing, disassembling, reassembling and install...
  • Removing rear swinging arm
  • Removing and installing flexible gaiter
  • Removing and installing threaded ring bearings
  • Removing bearing from left/right threaded ring
  • Installing bearing in left/right threaded ring
  • Removing drive shaft
  • Checking universal joint for wear
  • Installing drive shaft
  • Installing rear swinging arm
  • Removing and installing suspension strut
  • 34 BRAKES
  • Front brake calliper
  • Removing and installing front brake calliper
  • Removing and installing filler adapter
  • Removing and installing front brake pistons
  • Rear brake calliper
  • Removing and installing rear brake calliper
  • Removing and installing rear brake pistons
  • Removing and installing front brake disc
  • Removing and installing rear brake disc
  • Removing and installing front ABS sensor
  • Removing front ABS sensor ring
  • Adjusting front ABS sensor
  • Marking the ABS sensor ring
  • Checking/adjusting ABS sensor gap
  • Checking ABS sensor gap
  • Adjusting ABS sensor gap
  • Removing and installing rear ABS sensor
  • Adjusting rear ABS sensor
  • Marking the ABS sensor ring
  • Checking/adjusting ABS sensor gap
  • Checking ABS sensor gap
  • Adjusting ABS sensor gap
  • Removing and installing rear brake master cylinder...
  • Checking/adjusting play at piston rod
  • Checking play at piston rod
  • Adjusting play at piston rod
  • Removing and installing ABS control unit
  • Removing and installing ABS relay
  • Removing and installing front brake lines/hoses
  • Removing front brake lines/hoses
  • Preparatory work
  • Brake lines under fuel tank
  • Brake line/hose-telescopic fork
  • Brake hose-handlebar
  • Installing front brake lines/hoses
  • Removing and installing rear brake lines/hoses
  • Removing brake lines/hoses
  • Preparatory work
  • Brake hose-brake calliper
  • Brake hose-brake master cylinder
  • Brake fluid reservoir with return hose
  • Brake line-brake calliper
  • Installing brake lines/hoses
  • Checking brake pads for wear/ replacing brake pads...
  • See Group 00
  • Checking brake fluid level
  • See Group 00
  • Replacing brake fluid and bleeding brake system
  • See Group 00
  • 36 WHEELS AND TYRES
  • Removing and installing front wheel
  • Removing and installing wheel bearings
  • Removing left/right wheel bearings
  • Installing right/left wheel bearing
  • Installing left wheel bearing
  • Installing right wheel bearing
  • Removing/installing rear wheel
  • Removing rear wheel
  • Installing rear wheel
  • Static balancing of front and rear wheels
  • Static balancing of front wheel
  • Static balancing of rear wheel
  • Checking front/rear wheel rim for run-out
  • Checking front wheel rim for run-out
  • Checking rear wheel rim for run-out
  • 46 FRAME
  • Overview of fairing sections, K 1200 LT
  • Removing and installing fairing side section
  • Removing and installing mirror
  • Removing and installing fin
  • Removing and installing front turn indicator
  • Removing and installing bottom of tank cover
  • Removing and installing fairing skirt
  • Removing skirt
  • Removing and installing fairing side section
  • Removing and installing tank cover
  • Removing flap of radio compartment
  • Removing and installing engine spoiler
  • Removing/installing components mounted on side sec...
  • Removing air outlet duct
  • Removing kneepad
  • Removing grille
  • Removing badge
  • Removing rubber stop for radio cover
  • Removing and installing battery cover
  • Removing windscreen
  • Removing windscreen cover
  • Removing windscreen
  • Removing and installing windscreen adjuster
  • Removing and installing instrument cover
  • Removing and installing upper section of fairing
  • Removing and installing left/right handlebar trim
  • Removing and installing fork bridge cover
  • Removing/installing interior trim
  • Removing and installing left/right wind deflectors...
  • Removing and installing front mudguard
  • Removing and installing front mudguard front sect...
  • Removing and installing front mudguard rear secti...
  • Removing and installing front footrests
  • Removing and installing front right footrest plate...
  • Removing and installing front left footrest plate
  • Removing gearshift lever
  • Removing and installing left/right rear footrest p...
  • Removing and installing rear footrests
  • Disassembling rear footrest
  • Disassembling and assembling side stand
  • Removing and installing main (centre) stand
  • See Group 00, Lubricating main stand
  • Removing and installing intake air pipe
  • Removing and installing skirt bracket
  • Removing and installing crash bar
  • Removing and installing radiator holder
  • Removing and installing rear- mounted components
  • Removing and installing number-plate carrier
  • Removing and installing top case
  • Additional instructions for moving the backrest
  • Disassembling top case
  • Removing/installing interior light
  • Removing mirror and document stowage compartment
  • Removing lid of top case
  • Removing base of top case
  • Removing and installing rear carrier cover
  • Removing and installing case trimmer
  • Removing and installing side case
  • Removing and installing side case lid
  • Removing and installing rear moulding
  • Removing and installing rear carrier section
  • Removing rear mudguard
  • Removing and installing front fairing bracket
  • Removing reflectors
  • Removing upper reflector
  • Removing lower reflector
  • Removing and installing retaining plates in front ...
  • Checking running gear
  • Measuring wheel track offset
  • Example
  • Checking the leading link for deformation
  • See Group 31
  • Removing and installing frame
  • AND MORE....