• -$10.00
Vespa GTV 125 Workshop, Wiring & Parts Manuals
search
  • Vespa GTV 125 Workshop, Wiring & Parts Manuals

Vespa GTV 125 Workshop, Wiring & Parts Manuals

$29.95
$19.95 Save $10.00
No tax
Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

Vespa GTV 125 Workshop, Wiring & Parts Manuals

Workshop, service or specialist reference material, with separately identifiable wiring diagrams or circuit sections as specified in the original source. Coverage is limited to the indexed model variants.

Indexed technical areas: engine and mechanical systems, gearbox and transmission, braking and steering systems, suspension and axles, electrical components and circuits.

Examples from the original contents: Characteristics; Diagnostic code - 3 flashes; Inspecting the flywheel components; Shock-absorber - calliper bracket.

Important document scope / limitation: Workshop, parts catalogue and an explicitly listed wiring-diagram section are separate source components.

Original technical index

  • CONTENTS:
  • SERVICE MANUAL
  • Characteristics
  • - Rules
  • - Safety rules
  • - Maintenance rules
  • - Vehicle identification
  • - Dimensions and mass
  • - Engine
  • - Transmission
  • - Capacities
  • - Electrical system
  • - Frame and suspensions
  • - Brakes
  • - Wheels and tyres
  • - Carburettor
  • - 125cc Version
  • - Kehin
  • - Tightening Torques
  • - Overhaul data
  • - Assembly clearances
  • - Cylinder - piston assy.
  • - Crankcase - crankshaft - connecting rod
  • - Slot packing system
  • - Oversizes
  • - Products
  • Tooling
  • Maintenance
  • - Maintenance chart
  • - Carburettor
  • - Checking the spark advance
  • - Spark advance variation
  • - Spark plug
  • - Hub oil
  • - Check
  • - Replacement
  • - Air filter
  • - Engine oil
  • - Replacement
  • - Check
  • - Oil pressure warning light
  • - Checking the ignition timing
  • - Cooling system
  • - Braking system
  • - Level check
  • - Top-up
  • - Headlight adjustment
  • - SAS filters inspection and cleaning
  • Troubleshooting
  • - Engine
  • - Poor performance
  • - Rear wheel spins at idle
  • - Starting difficulties
  • - Excessive oil consumption/Exhaust smoke
  • - Insufficient lubrication pressure
  • - Engine tends-cut-off at full throttle
  • - Engine tends-cut-off at idle
  • - High fuel consumption
  • - Transmission and brakes
  • - Clutch grabbing or performing inadequately
  • - Insufficient braking
  • - Brakes overheating
  • - Electrical system
  • - Battery
  • - Turn signal lights malfunction
  • - Steering and suspensions
  • - Heavy steering
  • - Excessive steering play
  • - Noisy suspension
  • - Suspension oil leakage
  • Electrical system
  • - Conceptual diagrams
  • - Ignition
  • - Headlights and automatic starter section
  • - Battery recharge and starting
  • - Level indicators and enable signals section
  • - Devices and accessories
  • - Checks and inspections
  • - Immobiliser
  • - Virgin circuit
  • - Diagnostic codes
  • - Diagnostic code - 2 flashes
  • - Diagnostic code - 3 flashes
  • - Ignition circuit
  • - No spark plug
  • - Battery recharge circuit
  • - Stator check
  • - Voltage regulator check
  • - Recharge system voltage check
  • - Choke Inspection
  • - Turn signals system check
  • - Fuses
  • - Dry-charge battery
  • - Battery installation
  • Engine from vehicle
  • - Exhaust assy. Removal
  • - Removal of the engine from the vehicle
  • Engine
  • - Automatic transmission
  • - Transmission cover
  • - Air duct
  • - Removing the driven pulley shaft bearing
  • - Refitting the driven pulley shaft bearing
  • - Baffle roller
  • - Metallic roller
  • - Removal
  • - Refitting
  • - Removing the driven pulley
  • - Inspecting the clutch drum
  • - Removing the clutch
  • - Inspecting the clutch
  • - Pin retaining collar
  • - Removing the driven half-pulley bearing
  • - Inspecting the driven fixed half-pulley
  • - Inspecting the driven sliding half-pulley
  • - Refitting the driven half-pulley bearing
  • - Refitting the driven pulley
  • - Inspecting the clutch spring
  • - Refitting the clutch
  • - Refitting the driven pulley
  • - Drive-belt
  • - Removing the driving pulley
  • - Inspecting the rollers case
  • - Refitting the driving pulley
  • - Refitting the transmission cover
  • - End gear
  • - Removing the hub cover
  • - Removing the wheel axle
  • - Removing the hub bearings
  • - Removing the wheel axle bearings
  • - Removing the driven pulley shaft bearing
  • - Inspecting the hub shaft
  • - Inspecting the hub cover
  • - Refitting the wheel axle bearing
  • - Refitting the hub cover bearings
  • - Refitting the hub bearings
  • - Refitting the ub cover
  • - Flywheel cover
  • - Removing the hub cover
  • - Removing the stator
  • - Refitting the stator
  • - Refitting the flywheel cover
  • - Flywheel and starting
  • - Removing the flywheel magneto
  • - Inspecting the flywheel components
  • - Refitting the flywheel magneto
  • - Refitting the starter motor
  • - Cylinder assy. and timing system
  • - Removing the intake manifold
  • - Removing the rocker-arms cover
  • - Removing the timing system drive
  • - Removing the cam shaft
  • - Removing the cylinder head
  • - Removing the valves
  • - Removing the cylinder - piston assy.
  • - Inspecting the small end
  • - Inspecting the wrist pin
  • - Inspecting the piston
  • - Inspecting the piston rings
  • - Removing the piston
  • - Choosing the gasket
  • - Refitting the piston rings
  • - Refitting the cylinder
  • - Inspecting the cylinder head
  • - Inspecting the timing system components
  • - Inspecting the valve sealings
  • - Inspecting the valve housings
  • - Inspecting the valves
  • - Inspecting the springs and half-cones
  • - Refitting the valves
  • - Inspecting the cam shaft
  • - Refitting the head and timing system components
  • - Refitting the rocker-arms cover
  • - Refitting the intake manifold
  • - Crankcase - crankshaft
  • - Splitting the crankcase halves
  • - Inspecting the crankshaft alignment
  • - Inspecting the crankcase halves
  • - Inspecting the crankshaft plain bearings
  • - Refitting the crankcase halves
  • - Lubrication
  • - Conceptual diagrams
  • - Oil pressure check
  • - Crankshaft oil seals
  • - Refitting
  • - Oil pump
  • - Removing the oil sump
  • - Inspecting the by-pass valve
  • - Refitting the oil sump
  • - SAS valve
  • - Inspecting the one-way valve
  • - Inspecting the cut-off
  • - Fuel supply
  • - Removing the carburettor
  • - Kehin
  • - Refitting the carburettor
  • - Kehin
  • - Level check
  • - Kehin
  • - Inspecting the valve and needle
  • - Kehin
  • - Inspecting the automatic choke device
  • - Kehin
  • - Adjusting the idle
  • Suspensions
  • - Front
  • - Removing the front wheel
  • - Front wheel hub overhaul
  • - Refitting the front wheel
  • - Steering column
  • - Removal
  • - Overhaul
  • - Refitting
  • - Front shock absorber
  • - Removal
  • - Refitting
  • - Shock-absorber - calliper bracket
  • - Overhaul
  • - Rear
  • - Removing the rear wheel
  • - Refitting the rear wheel
  • - Swing-arm
  • - Removal
  • - Overhaul
  • - Refitting
  • - Shock absorbers
  • - Removal
  • - Refitting
  • - Exhaust bracket
  • - Removal
  • - Refitting
  • - Centre-stand
  • - Side stand
  • Braking system
  • - Rear brake calliper
  • - Removal
  • - Overhaul
  • - Refitting
  • - Front brake calliper
  • - Removal
  • - Overhaul
  • - Refitting
  • - Rear brake disc
  • - Removal
  • - Refitting
  • - Disc Inspection
  • - Front brake disc
  • - Removal
  • - Refitting
  • - Disc Inspection
  • - Front brake pads
  • - Removal
  • - Refitting
  • - Rear brake pads
  • - Removal
  • - Refitting
  • - Fill
  • - Front
  • - Brake fluid level check
  • - Front brake pump
  • - Removal
  • - Overhaul
  • - Refitting
  • Cooling system
  • - Water pump - overhaul
  • - Check
  • Chassis
  • - Seat
  • - Rear rack
  • - Instrument panel
  • - Headlight assy.
  • - Knee-guard
  • - Removing the ignition key-switch when on *off*
  • - Removing the ignition key-switch when on *lock*
  • - Front wheel housing
  • - Taillight assy.
  • - Footrest
  • - Side fairings
  • - Rear mudguard
  • - Helmet bay
  • - Fuel tank
  • - Rear central cover
  • - Front mudguard
  • - Radiator fan
  • - Front central cover
  • Pre-delivery
  • - Aesthetic inspection
  • - Tightening torques inspection
  • - Electrical system
  • - Levels check
  • - Road test
  • - Static test
  • - Functional inspection
  • Time
  • - Engine
  • - Crankcase
  • - Crankshaft
  • - Cylinder assy.
  • - Cylinder head assy.
  • - Rocker arms support assy.
  • - Cylinder head cover
  • - Chain tensioner
  • - Oil filter
  • - Driven pulley
  • - Oil pump
  • - Final gear assy.
  • - Driving pulley
  • - Transmission cover
  • - Starter motor
  • - Flywheel magneto
  • - Carburettor
  • - Exhaust pipe
  • - Air cleaner
  • - Frame
  • - Centre-stand
  • - Footrests
  • - Rear cover
  • - Underseat compartment
  • - Mudguard
  • - Fuel tank
  • - Expansion tank
  • - Rear shock-absorber
  • - Steering column bearings
  • - Handlebar covers
  • - Handlebar components
  • - Swing-arm
  • - Brake hoses
  • - Seat
  • - Instrument panel
  • - Rear rack
  • - Locks
  • - Turn signal lights
  • - Front wheel
  • - Rear wheel
  • - Electric devices
  • - Front suspension
  • PARTS CATALOGUE
  • WIRING DIAGRAMS