Cfmoto 450SS from 2025 - Service Manual - Repair Manual
Digital technical documentation with sections on Operational Precautions, Disassembly and Assembly Precautions, Location of VIN and EIN. Review the complete contents below for the systems and procedures covered.
Manual contents
- 01 GENERAL INFORMATION
- - 1.1 Operational Precautions
- - 1.2 Disassembly and Assembly Precautions
- - 1.3 Location of VIN and EIN
- - 1.4 Fuel Evaporation System Diagram
- 02 MAINTENANCE INFORMATION
- - 2.1 Pre-Trip Maintenance Schedule
- - 2.2 Break-In Maintenance Schedule
- - 2.3 Periodic Maintenance Schedule
- 03 TECHNICAL INFORMATION
- - 3.1 General Specifications
- - 3.2 Engine Specifications
- - 3.3 Vehicle Service Specifications
- - 3.3.1 Front Wheel
- - 3.3.2 Rear Wheel
- - 3.3.3 Brake System
- - 3.3.4 Lighting, Dashboard and Switches
- - 3.3.5 Suspension
- - 3.4 Engine Service Specifications
- - 3.4.1 Valve Train and Cylinder Head
- - 3.4.2 Lubrication System
- - 3.4.3 Cylinder, Piston, Piston Ring and Connecting Rod
- - 3.4.4 Clutch and Transmission
- - 3.4.5 Cooling System
- - 3.4.6 Air Inlet System
- - 3.4.7 Electrical System
- - 3.5 Torque Tables
- - 3.5.1 Torque Table for Vehicle
- - 3.6 Consumption and Assembly Materials
- - 3.6.1 Vehicle Consumption Materials
- - 3.6.2 Engine Consumption and Assembly Materials
- 04 VEHICLE
- - 4.1 Preparation Notes
- - 4.2 Seat
- - 4.2.1 Seat Removal
- - 4.2.2 Seat Installation
- - 4.3 Body Covering Parts
- - 4.3.1 Headlight LH&RH Guards
- - 4.3.2 Windshield and Rearview Mirrors
- - 4.3.3 Engine Panel
- - 4.3.4 Headlight Upper Press Cover
- - 4.3.5 Wings
- - 4.3.6 Dashboard
- - 4.3.7 Fuel Tank Upper Guard
- - 4.3.8 Radiator Guard Assembly
- - 4.3.9 Rear Panel
- - 4.3.10 Vehicle Cover
- - 4.3.11 Front Fender
- - 4.4 Fuel Tank
- - 4.4.1 Depressurizing Fuel Hose
- - 4.4.2 Fuel Tank Removal
- - 4.4.3 Fuel System Inspection
- - 4.4.3.1 EFI Fuel Filter
- - 4.4.3.2 Fuel Pump
- - 4.4.3.3 Fuel Level Sensor
- - 4.4.4 Fuel Tank Installation
- - 4.5 Cooling System
- - 4.5.1 Coolant Drain
- - 4.5.2 Radiator Removal
- - 4.5.3 Radiator Inspection
- - 4.5.3.1 Radiator Fin Inspection
- - 4.5.3.2 Filler Cap Pressure Inspection
- - 4.5.3.3 Fan Inspection
- - 4.5.3.4 Coolant Inspection, Addition and Replacement
- - 4.6 Muffler Assembly
- - 4.6.1 Muffler Removal
- - 4.6.2 Muffler Inspection
- - 4.6.3 Oxygen Sensor
- - 4.7 Wheels, Brakes and Shock Absorbers
- - 4.7.1 Front Brake Caliper and Front Wheel Removal
- - 4.7.2 Rear Brake Caliper and Rear Wheel Removal
- - 4.7.3 LH&RH Foot Pedal Removal
- - 4.7.4 Rear Shock Absorber and Rear Fork Removal
- - 4.7.5 Chain Removal
- - 4.7.5.1 Chain Repairs
- - 4.7.5.2 Chain Tension Inspection
- - 4.7.5.3 Chain Cleaning and Maintenance
- - 4.7.6 Rear Wheel Inspection
- - 4.7.7 Tire Pressure
- - 4.7.8 Tire Surface
- - 4.7.9 Wheel Bearing
- - 4.7.10 Front Shock Absorber Removal
- - 4.7.11 Brake Master Cylinders
- - 4.7.11.1 Brake Fluid Inspection
- - 4.7.11.2 Brake Fluid Replacement
- - 4.7.12 Brake Line
- - 4.7.13 Brake Caliper and Brake Disc Inspection
- - 4.7.14 Brake Free Play
- - 4.7.15 MAB Execution Unit
- 05 ELECTRICAL SYSTEM
- - 5.1 Diagnostic Tools
- - 5.2 Preparation Notes
- - 5.3 Battery
- - 5.4 Dashboard
- - 5.5 Headlight
- - 5.5.1 Headlight Removal
- - 5.5.2 Headlight Adjustment
- - 5.6 Left Handlebar Switch
- - 5.7 Right Handlebar Switch
- - 5.8 Ignition Switch
- - 5.9 Starter Relay
- - 5.10 T-BOX
- - 5.11 Relay Seat and Fuse Box
- - 5.12 Regulator
- - 5.13 Flasher
- - 5.14 ECU
- - 5.15 Taillights
- - 5.16 Horn
- - 5.17 MSE 6.0 Fault Codes
- - 5.18 Fault Diagnosis
- - 5.19 Fault Diagnosis by Engine Problem
- 06 SELECT ENGINE TOPICS
- - 6.1 Air Filter
- - 6.2 Throttle Valve
- - 6.2.1 Throttle Valve Body Removal
- - 6.2.2 Throttle Body Cleaning
- - 6.2.3 Fuel Injector
- - 6.2.4 Intake Temperature Pressure Sensor
- - 6.2.5 Throttle Position Sensor
- - 6.2.6 Stepping Motor
- - 6.3 Water Temperature Sensor
- - 6.4 Trigger
- - 6.5 Ignition Coil
- - 6.6 Clutch Cable
- - 6.7 Engine Removal
- - 6.8 Throttle Cable Free Play
- 07 ENGINE
- - 7.1 Preparation Notes
- - 7.1.1 Unit Conversion Table
- - 7.1.2 Warnings
- - 7.2 Maintenance Information
- - 7.2.1 Engine Appearance
- - 7.2.2 General Precautions
- - 7.2.3 Selection of Fuel and Oil
- - 7.2.4 Engine Break-In
- - 7.2.5 Special Engine Maintenance Tools
- - 7.3 Engine Disassembly
- - 7.3.1 Stabilize the Engine
- - 7.3.2 Drain Engine Oil
- - 7.3.3 Starter Motor Removal
- - 7.3.4 Thermostat Removal
- - 7.3.5 Pump Removal
- - 7.3.6 Cylinder Head Cover Removal
- - 7.3.7 RH Cover Removal
- - 7.3.8 Clutch Removal
- - 7.3.9 Shift Lever and Positioning Components Removal
- - 7.3.10 Oil Pump Removal
- - 7.3.11 Cylinder Head Removal
- - 7.3.12 Magneto and Double Gear Removal
- - 7.3.13 Cylinder Body Removal
- - 7.3.14 Piston Removal
- - 7.3.15 Oil Pan Removal
- - 7.3.16 Oil Cooler Removal
- - 7.3.17 Compartment
- - 7.4 Engine Inspection
- - 7.4.1 Crankcase
- - 7.4.1.1 Selecting Plain Bearing
- - 7.4.1.2 Crankcase
- - 7.4.1.3 RH Side Cover
- - 7.4.2 Cylinder Head Cover Assembly
- - 7.4.3 Cylinder Head Assembly
- - 7.4.4 Cylinder Body
- - 7.4.5 Piston / Piston Ring / Piston Pin
- - 7.4.6 Distribution Drive
- - 7.4.7 Crankshaft Connecting Rod
- - 7.4.8 Clutch
- - 7.4.9 Shift Gear
- - 7.4.9.1 Main Shaft
- - 7.4.9.2 Countershaft
- - 7.4.9.3 Shift Fork
- - 7.4.9.4 Shift Drum
- - 7.4.9.5 Gearshift Lever Assembly
- - 7.4.10 Lubrication System
- - 7.4.10.1 Lubricating Chart
- - 7.4.10.2 Oil Pump
- - 7.4.10.3 Oil Pressure Relief Valve
- - 7.4.10.4 Oil Cooler
- - 7.4.11 Water Pump Assembly
- - 7.4.12 Electric Starter
- - 7.4.13 Magneto Stator
- - 7.4.14 Rear Balance Shaft Assembly
- - 7.5 Engine Assembly
- - 7.5.1 Rear Balance Shaft Assembly Installation
- - 7.5.2 Shift Drum, Position Cam, and Position Swing Arm Installation
- - 7.5.3 Countershaft Installation
- - 7.5.4 Fork Shaft and Gearshift Fork Installation
- - 7.5.5 Main Shaft Installation
- - 7.5.6 Gearshift Lever Installation
- - 7.5.7 Crankshaft Connecting Rod and Front Balance Shaft Installation
- - 7.5.8 Crankcase Closing
- - 7.5.9 Oil Pump and Oil Pressure Switch Installation
- - 7.5.10 Water Pump Installation
- - 7.5.11 Oil Pan Installation
- - 7.5.12 Oil Cooler Installation
- - 7.5.13 Oil Filter Installation
- - 7.5.14 Cylinder Body and Piston Installation
- - 7.5.15 Timing Chain Installation
- - 7.5.16 Cylinder Head Installation
- - 7.5.17 Magneto Rotor Assembly Installation
- - 7.5.18 LH Side Cover Installation
- - 7.5.19 Intake and Exhaust Camshaft Installation
- - 7.5.20 Hydraulic Tensioner Installation
- - 7.5.21 Cylinder Head Cover Installation
- - 7.5.22 Starter Motor Installation
- - 7.5.23 Clutch Installation
- - 7.5.24 RH Side Cover Installation
- - 7.5.25 Gear Sensor Installation
- - 7.5.26 Oil Cooler Water Inlet and Outlet Hose Installation
- - 7.5.27 Throttle and Fuel Pipe Assembly Installation
- - 7.5.28 Output Sprocket Installation
- - 7.5.29 Oil Filling, Oil Level Inspection, and Oil Pressure Inspection
- 08 CLEANING AND STORAGE
- - 8.1 Motorcycle Cleaning
- - 8.2 Inspection and Maintenance in Winter
- - 8.3 Parking
- - 8.4 Motorcycle Use After Storage