- -$10.00
Comprehensive power source distribution schematics and main power supply lines (including pre- and post-May 2014 production changes), diagnostic link connector (DLC3) wiring, and dedicated ground point layouts across body, instrument panel, and engine compartments for LHD and RHD configurations.
Detailed relay box and junction block locations covering body, engine compartment, instrument panel, engine room relay blocks (R/B) and junction boxes (J/B), fusible link block assemblies, and inner circuit diagrams for Junction Boxes No. 6 and No. 7.
Engine control and cruise control schematics covering petrol and diesel engine variants (1NR-FE, 1ND-TV, and 1NZ-FE, with specific production breakpoints for 1NZ-FE before and after August 2012).
Charging system circuits for 1NR-FE, 1ND-TV, and 1NZ-FE engines, ignition wiring, starting system schematics for models with and without entry and start systems, Stop & Start system wiring (1NR-FE and 1NZ-FE), and cooling fan circuits.
Chassis control and braking electronics wiring covering Anti-lock Braking Systems (ABS with and without VSC), Traction Control (TRC), Vehicle Stability Control (VSC), and Electric Power Steering (EPS).
Transmission and driveline wiring covering CVT and shift indicators, multi-mode manual transmission circuits, and tire pressure warning systems (TPWS).
Climate control wiring diagrams covering automatic and manual air conditioning systems, and combustion-type power heaters.
Convenience and interior access circuits including power windows for LHD and RHD models, door lock controls, double locking systems, remote control mirrors, roof sunshade systems, seat heaters, back door openers, power outlets, and cigarette lighters.
Complete exterior and interior lighting schematics covering headlights (with and without automatic light control, Hong Kong and general variants, across pre- and post-May 2014 production breaks), front and rear fog lights, taillights, illumination, stop lights, backup lights, turn signals, and hazard warning lights.
Instrumentation and driver visibility circuits including combination meters, automatic light control, light auto-off systems, front and rear wipers and washers (with and without auto wiper systems), automatic and manual headlight beam level controls, mirror heaters, rear window defoggers, automatic glare-resistant EC mirrors, light reminders, and key reminders.
Audio system, navigation system, and parking assist rear-view monitor schematics.
Multiplex communication system (CAN bus) network wiring covering pre- and post-May 2014 production specifications.
Passive safety and security schematics featuring SRS airbag systems, driver and passenger seat belt warning circuits, engine immobiliser systems, steering lock controls, entry and start systems, wireless door lock controls, and theft deterrent systems.
Exhaustive component placement, wiring harness routing, and ground point location guides mapped across body sections, instrument panels, and engine compartments (1ND-TV, 1NR-FE, 1NZ-FE) for left-hand and right-hand drive models.
Nothing burns shop time faster than probing a junction block that doesn't match your schematic. On the Toyota Verso-S and Ractis (XP120 platform), assuming a 2011 wiring harness shares the same pinouts as a 2015 model is a costly diagnostic mistake.
In practical diagnostics, the May 2014 production split is notorious. Toyota overhauled the Power Source distribution, Illumination/Taillight circuits, and the CAN Multiplex Communication System on vehicles built from May 2014 onward. If you are trying to trace a communication fault between the combination meter and the ABS module on a late-model XP120 using a pre-2014 diagram, the pin numbers and splice locations will simply be wrong. Similarly, 1NZ-FE engine control and Continuously Variable Transmission (CVT) shift indicator circuits saw a distinct wiring revision around August 2012.
This 856-page technical resource eliminates that guesswork by providing the exact factory-separated schematics for every production split, engine variant, and regional market.
| August 2012 Production Revision | May 2014 Production Revision |
|---|---|
|
|
Electrical troubleshooting on modern subcompacts requires a clear view of how the engine control module interfaces with drivetrain and safety electronics. This workshop reference covers the full wiring layout for all three primary XP120 powertrains: the 1.33L 1NR-FE (Dual VVT-i), the 1.5L 1NZ-FE (VVT-i), and the 1.4L 1ND-TV (D-4D diesel).
During troubleshooting, you'll find dedicated circuits for:
Mechanic's Field Note: A common workshop scenario on the Verso-S involves a no-start condition accompanied by an unresponsive Smart Entry & Start System. Don't immediately condemn the certification ECU. Instead, verify the ground points along the instrument panel harness and check the specific "w/ Entry & Start System" immobiliser loop schematics; high resistance at the interior grounding bolts frequently mimics a dead smart key module.
Any automotive electrician knows that colored wire paths are only half the battle. When dealing with parasitic draw diagnosis or erratic component behavior, you need to see inside the fuse boxes.
This technical document goes beyond basic point-to-point lines by detailing the internal circuits for every major relay and junction block:
Furthermore, Left-Hand Drive (LHD) and Right-Hand Drive (RHD) vehicles feature completely different body and dashboard wiring harnesses. The manual provides separate, exhaustive component and ground point location diagrams for both LHD and RHD layouts across the engine compartment, dashboard, body shell, and under-seat seating areas.
Whether you are restoring a collision vehicle or repairing a localized electrical failure, this guide covers every secondary and comfort system on the XP120 chassis:
We know that when a vehicle is torn down in the service bay, you don't have time to wait for shipping or deal with restricted software packages.
Once your checkout is processed through PayPal, Credit Card, Apple Pay, or Google Pay, our server generates an instant, secure download link sent directly to your inbox and accessible via your customer account. Your access link remains active for 10 days or up to 10 downloads, giving you plenty of time to save the 856-page PDF to your shop laptop, diagnostic tablet, or mobile device.
In the rare event of a browser or network routing error, our team provides guaranteed backup file delivery via Dropbox. If you are unfamiliar with managing large technical PDFs on your device, check out our quick video walkthrough at https://servicemanuals.info/How-to-Download.mp4.
Get immediate access to the full service manual and start diagnosing with precision.
Why am I getting erratic communication errors between the ABS module and the combination meter on a late-2014 Toyota Ractis?
This symptom often points to a mismatch in CAN-bus wiring references. Toyota modified the Multiplex Communication System (CAN) architecture and primary Power Source circuits starting in May 2014. Using a pre-May 2014 schematic will lead you to test the wrong junction block pins. This reference includes the dedicated post-May 2014 CAN diagrams required to isolate open or shorted data lines accurately.
How does this guide handle regional differences like Right-Hand Drive or Hong Kong market lighting systems?
Unlike generic manuals that merge regional variations into confusing, single-page diagrams, this document separates them. You will find distinct wiring harnesses and component location maps for LHD and RHD cabin/body configurations, along with specific schematics for Hong Kong market Headlight and Front Fog Light option connectors (covering both pre- and post-production date changes).
Can I use this manual to trace parasitic battery drains through the dashboard fuse boxes?
Yes. Tracing a parasitic draw requires knowing how circuits are bridged inside the fuse blocks. This guide includes complete internal circuit diagrams for the Instrument Panel Junction Block Assembly, Fusible Link Blocks, and auxiliary blocks (J/B No. 6 and No. 7), allowing you to see which circuits remain hot without pulling every fuse blindly.
What makes the 1NR-FE and 1NZ-FE Stop & Start wiring diagrams different?
The dual-engine Auto Stop & Start implementations on the XP120 use different engine control interfaces and charging feedback loops. This document dedicates separate, complete electrical wiring sections to the 1NR-FE Stop & Start System and the 1NZ-FE Stop & Start System, ensuring you are testing the correct voltage thresholds and sensor inputs for your specific engine code.