Porsche 968 1992-1995 - Service Manual - Wiring Diagram - Parts Manual
Digital technical documentation with sections on 968 WORKSHOP MANUAL, Engine support, Fuel Supply. Review the complete contents below for the systems and procedures covered.
Manual contents
- WORKSHOP MANUAL 1992-1995 (801 pages)
- 968 WORKSHOP MANUAL
- Structure of the Workshop Manual
- VOL I - ENGINE
- General
- Technical data
- Maintenance, Self Diagnosis general
- Maintenance
- Operating instructions for system tester 9288
- Engine, Crankcase, Engine Mounts
- Tolerances and wear limits
- Tightening torques for engine
- Removing and installing engine (Manual transmission)
- Removing and installing engine (Tiptronic transmission)
- Engine, Crankshaft, Pistons
- Adjusting guide rail for balance shaft toothed belt
- Checking adjustment of balance shafts
- Fitting toothed belt for balance shaft
- Adjusting Special Tool 9201
- Checking and adjusting balance shaft toothed belt tension
- Crankcase markings
- Locking the flywheel for assembly work
- Engine support
- Crankcase - Tools
- Machining cylinder bores in upper crankcase section
- Crankcase - Installation length or protrusion length of studs
- Dismantling and assembling crankcase, crankshaft
- Aligning the upper and lower parts of the crankcase
- Crankshaft - Standard and Repair dimensions
- Dimantling and assembling pistons, connecting rod
- Checking piston and cylinder bore
- Dismantling and assembling balance shaft drive
- Removing and installing double-mass flywheel and grooved ball bearing
- Engine, Cylinder Head, Valve Drive
- Replacing the camshaft toothed belt (with hydraulic belt tensioner)
- Adjusting and checking the camshaft setting
- Applying TDC mark-camshaft sprocket
- Camshaft adjustment gauge (shop made)
- Fitting the camshafts
- Fitting the camshaft seal
- Camshaft references
- Machining the cylinder head mating surface
- Removing and installing the cylinder head
- Valve dimensions
- Dismantling and assembling camshaft drive
- Engine, Lubrication
- Removing and installing lubrication system components
- Dismantling and assembling oil pressure release valve
- Removing and installing oil restraining valve
- Checking oil pressure
- Cleaning the entire oil system
- Engine, Cooling
- Mixing table
- Checking cooling and heating system for tightness
- Fuel Supply
- Fuel vacuum line routing
- Fuel System - Electronic Ignition
- Test values
- Checking idle and CO level of vehicles without catalytic converter
- Checking idle and CO level of vehicles with catalytic converter
- Removing and installing DME injection system components
- Removing and installing injection valves
- Ignition System
- Replacing spark plugs
- DME control units as of Model Year ' 92
- Removing and installing knock sensors
- DME-Diagnosis / Troubleshooting
- VOL II - MANUAL TRANSMISSION
- General
- Technical data
- Clutch, operation
- Removing and installing clutch
- Identification of clutch pressure plates
- Adjusting the clutch pedal
- Manual Transmission, Operation, Housing
- Removing and installing transmission
- Adjusting gearshift
- Removing and installing gear set
- Removing and installing drive shaft seal if transmission has not been dismantled
- Removing and installing 5th and 6th gear
- Determining snap rings for tapered roller bearing and 6th gear gearwheel
- Removing and installing drive pinion and drive shaft
- Dismantling and assembling end cover
- Recalculating adjusting shim ,,S4''
- Dismantling and assembling end shield
- Dismantling and assembling transmission housing
- Manual Transmission, Gears, Shafts
- Dismantling and assembling drive shaft
- Dismantling and assembling drive pinion
- Differential / Transaxle System
- Removing and installing differential
- Dismantling and assembling differential
- Adjusting drive set
- VOL II - TIPTRONIC TRANSMISSION
- General
- Technical data
- Diagnosis
- Diagnosis Tiptronic / Troubleshooting
- Troubleshooting mechanical / hydraulic section
- Clutch, Automatic Torque Converter
- Removing and installing the torque converter
- Removing and installing the rotary shaft seal for the torque converter
- Automatic Transmission, Operation, Housing
- Removing and installing the transmission
- Keylock and Shiftlock Check Points / Adjustment operations
- Shiftlock - Emergency operation
- Removing and installing multi-function switch-transmission
- Adjusting bowden cable for selector device
- Automatic Transmission, Gears, Controls
- Checking the ATF level
- Changing the ATF level
- Flushing ATF radiator and piping system
- Removing and installing inductive engine speed pickup
- Removing and installing hydraulic control unit
- Removing and installing transmission wiring harness
- Removing and installing solenoid
- Removing and installing piston for brake band C '
- Removing and installing spacer
- Removing and installing spacer seals
- Checking end play
- Removing and installing ATF pump
- Dismantling and assembling ATF pump
- Differential / Transaxle System
- Changing the transmission oil in rear-axle drive
- Removing and installing spur gear drive
- Replacing gasket between housing and housing flange of spur gear drive
- Removing and installing output shaft
- Removing and installing differential
- VOL III - CHASSIS, BODY
- Front Wheel Suspension
- Torque specifications- Front axle
- Technical Data 968 / 968 CS
- Adjusting the front wheel bearings
- Dismantling and assembling suspension
- Rear Wheel Suspension, Drive Shaft
- Torques specifications - rear axle
- Technical data 968 / 968 CS
- Disassembling and assembling suspension
- Wheels, Tires, Alignment
- Wheels and tires
- Fitting 16" and 17" cup design wheels-the vehicle
- Wheel mounting as of MY '94
- Wheels and tires of the 968 CS
- Sample measuring chart
- Adjustment values for wheel alignment
- Suspension alignment
- Tire fitting
- Brakes, Mechanical
- Technical data
- Torque specifications - mechanical brake system
- Checking thickness of brake pads
- Removing and installing brake pads
- Adjusting the brake pushrod
- Checking stop light switch adjustment
- Checking and adjusting the parking brake
- Checking brake disc lateral runout
- Checking brake disc thickness
- Brakes - Hydraulics, Regulator, Booster
- Torques specifications - hydraulic brake system
- Changing the brake fluid / bleeding the brakes
- Steering
- Torque specifications - steering
- Technical data 968 / 968 CS
- Removing and installing ignition steering lock
- Replacing ignition switch
- Replacing lock barrel of ignition steering lock
- Body - General
- Safety notes
- Checking dimensions for body repairs
- Checking dimensions for body repairs - Cabriolet
- Special Tools and Metalworking Repair Tools
- Body - Front
- Replacing part of front end
- Bodywork - Center
- Replacing part of door sill with side member and floor pan
- Replacing complete roof
- Body - Rear
- Replacing part of rear end
- Lids
- Dismantling and assembling front cover
- Doors
- Removing and fitting door outer handle
- Dismantling and assembling door outer handle
- Convertible Top
- Removing and installing convertible top
- Bumpers
- Removing and fitting spoiler and bumpers
- Removing and fitting rear spoiler and bumper
- Glasses, Window Controls
- Bonding the interior rearview mirror in place
- Removing and installing windshield - 2-pack adhesive
- Removing and installing rear side window - 2-pack adhesive
- Exterior Equipment
- Body paint colors beginning with 1992 models
- Removing and installing plastic end and side applicates - Cabriolet
- Removing and installing tank flap - Cabriolet
- Removing and installing door mirror
- Removing and fitting side member panel
- Removing and installing badge on cover
- Removing and installing wheel housing liner
- Interior Equipment / Airbag
- Inspecting seat belts
- Safety Precautions for Working on Cars with Airbag
- Replacing cover for passenger airbag
- Removing and installing Airbag Steering wheel
- Removing and installing Airbag components
- Checking Airbag System Operation
- Correct disposal of airbag units
- Repairing horn buttons of airbag steering wheel
- Diagnosis / Troubleshooting Airbag
- Seats
- Checking seat heating
- Calibrating controllable seat heating
- VOL IV - HEATING, VENTILATION, AIR CONDITION, ELECTRICS
- Air Conditioning
- Technical data of air conditioning system as of MY ' 93
- Pressure and temperature specifications
- Radio, Telephone, On-board Computer
- Removing and installing antenna
- Exterior Lights, Lamps, Switches, outside
- Adjusting the pop-up headlight mechanical system
- Checking headlight beam adjuster
- Instruments, Fuel Gauge, Alarm System
- Diagnosis / troubleshooting alarm system
- VOL V - WIRING DIAGRAMS
- Wiring
- Passenger compartment wiring harness for 968 CS
- Repairing the Tiptronic wiring harness
- Routing the sensor wire at the Tiptronic transmission
- Wiring diagram Model ' 92
- Wiring diagram Model ' 93
- Wiring diagram Model ' 94
- Wiring diagram Model ' 95
- PORSCHE 968 - HISTORY
- 968 history
- Option codes
- 968 specifications
- Founders
- Production numbers
- Chassis numbers
- PARTS CATALOG 1992-1995 (346 pages)
- MAIN GROUP 0: ACCESSORIES AND OTHERS
- 001: tools, stickers
- 002: inst set, snow chains, roof rack system
- 004: paint touch-up applicator
- 005: securing liquid, sealing compound
- MAIN GROUP 1: ENGINE
- 101: replacement engine, crankcase, protective plate
- 102: crankshaft, pistons
- 103: cylinder head, camshaft, valve
- 104: engine lubrication
- 105: water cooling
- 106: air cleaner
- 107: lh-jetronic
- 109: engine suspension
- 198: repair kits
- MAIN GROUP 2: FUEL SYSTEM, EXHAUST SYSTEM
- 201: fuel system, tank, etc.
- 202: exhaust system, catalytic converter
- 298: repair kits
- MAIN GROUP 3: TRANSMISSION
- 301: central tube, clutch
- 302: replacment transmission, transmission case
- 303: gear sets, shafts
- 304: shifts rods, forks
- 305: differential
- 306: transmission suspension
- 310: central tube, tiptronic
- 320: replacement transmission, tiptronic
- 330: converter, tiptronic
- 340: oil sump, oil attrainer, tiptronic
- 360: atf-cooler, atf-pipes, tiptronic
- 370: transmission suspension, tiptronic
- 398: repair kits, manual transmission, TIPTRONIC
- MAIN GROUP 4: FRONT AXLE, STEERING
- 401: track control arm, cross member, air deflector
- 402: springs, shock absorber, stabilizer
- 403: steering, airbag
- MAIN GROUP 5: REAR AXLE
- 501 rear axle, dirve shaft
- 502: vibration damper, stabilizer
- 598: repair kits
- MAIN GROUP 6: WHEELS, BRAKES
- 601: wheels
- 602: disk brake, front
- 603: disk brake, rear, hand brake
- 604: brake master cylinder, brakeservo, reservoir, lines
- 605: hydraulic unit, antiblock system
- 698: repair kits
- MAIN GROUP 7: HAND LEVER SYSTEM, PEDAL SYSTEM
- 701: gear shift lever, hand brake lever
- 702: pedal system
- MAIN GROUP 8: BODY
- 801: body, frame, fender
- 802: bumper, front embellisher, linings
- 803: covers, spoiler
- 804: doors
- 805: glasses
- 806: concealing headlamps
- 807: sound absorber, linings
- 808: seats
- 809: dashboard, rear-view-mirror
- 810: molding
- 811: lifting roof, folding top, sealing
- 812: seat belt
- 813: ventilation, heater, air conditioner
- 898: repair kits
- MAIN GROUP 9: ELECTRICAL EQUIPMENT
- 901: electr. equipment engine, control unit, alternator, distributor
- 902: starter, battery, harnesses
- 903: switches, clock, temperture gauge, central electr. equipment, relay, horn
- 904: windshield wiper system
- 905: headlamp, turning signal, interior lights
- 906: instruments, sensor
- 907: tempomat
- 909: anti-theft device
- 910: electrical fan
- 911: radio, telephone, loudspeaker, antenna
- MSP-PAGES
- V-PAGES