2012 & Up Index
- Polaris Ranger RZR 570, including Standard and International (INTL) configurations.
- 2012 Ranger RZR 570 workshop service and repair manual.
- 2012 electrical wiring diagrams, chassis harness diagrams, cargo box harness diagrams and wiring harness routing.
- Additional 2013 Polaris RZR 570 Owner's Manual.
- Technical documentation covering engine overhaul, electronic fuel injection, PVT clutch system, transmission, AWD drivetrain, steering, suspension, brakes and electrical systems.
General Information & Technical Specifications
- Vehicle identification, model designation, engine identification number and VIN information.
- Vehicle and engine serial number locations, replacement keys and publication references.
- Technical specifications for 2012 RZR 570 and International models.
- Standard and metric bolt tightening torques, measurement conversions and special service tools.
- Workshop reference tables, mechanical specifications and component assembly information.
Periodic Maintenance & Inspection
- Scheduled maintenance intervals, pre-ride inspections and engine break-in procedures.
- General vehicle inspection, chassis fasteners and lubrication points.
- Engine oil level inspection, oil and filter replacement, valve clearance inspection and compression testing.
- Air filter, intake pre-filter, fuel lines, fuel pump and throttle pedal maintenance.
- Transmission and front gearcase lubrication, fluid inspection and replacement.
- Cooling system inspection, coolant replacement and cooling system pressure testing.
- Steering, suspension, brakes, tyres, wheel hubs and drive shaft boot inspection.
- Battery maintenance, spark plug replacement and electrical grounding checks.
Engine Mechanical Service & Overhaul
- Engine removal and installation, engine mountings and top-end servicing with the engine installed.
- Cylinder head removal, disassembly, inspection and assembly.
- Camshafts, camshaft sprockets, timing chain, chain guides and exhaust camshaft decompression mechanism.
- Valves, valve seats, combustion chamber inspection, valve clearance adjustment and valve shim selection.
- Cylinder inspection, piston removal, piston rings, connecting rod inspection and cylinder honing procedures.
- Piston-to-cylinder clearance, piston ring gap measurements and mechanical service specifications.
- Crankcase disassembly, crankshaft inspection, balance shaft servicing and internal engine bearing replacement.
- Flywheel, stator housing, starter one-way clutch, oil pump and crankcase breather servicing.
- Engine top-end and bottom-end assembly, camshaft timing and balance shaft timing procedures.
Engine Lubrication & Cooling System
- Engine lubrication specifications, oil pressure testing and engine oil flow diagrams.
- Oil pump removal and assembly, oil pickup inspection and oil pressure regulator valve servicing.
- Engine cooling system exploded views and coolant circulation diagrams.
- Radiator servicing, thermostat replacement and cooling system pressure cap testing.
- Water pump impeller, mechanical seal and oil seal replacement.
- Cooling system draining, filling, bleeding and troubleshooting procedures.
Electronic Fuel Injection (EFI) & Fuel System
- EFI system operation, component identification, exploded views and component locations.
- Electronic Control Unit (ECU) operation, servicing and replacement.
- Fuel tank removal and installation, fuel lines and quick-connect fittings.
- Fuel injector operation, testing, troubleshooting and replacement.
- Fuel pump operation, fuel pressure-related servicing, pump testing and replacement.
- Fuel level sender testing and fuel system inspection.
- Initial fuel priming and starting procedures.
- EFI electrical system diagram and engine management diagnostics.
Engine Sensors & Electronic Management
- Temperature and Manifold Absolute Pressure (T-MAP) sensor testing and replacement.
- Crankshaft Position Sensor (CPS) inspection and replacement.
- Idle Air Control (IAC) system operation, testing and replacement.
- Throttle Position Sensor (TPS) resistance testing and adjustment-related procedures.
- Engine Coolant Temperature (ECT) sensor testing and replacement.
- Ignition coil testing and high-tension lead replacement.
- ECU diagnostics, fault code identification and electronic fuel injection troubleshooting.
Polaris Digital Wrench Diagnostics
- Polaris Digital Wrench diagnostic software operation and system overview.
- Diagnostic connector information, software versions and updates.
- Guided diagnostics and communication error troubleshooting.
- ECU replacement and engine controller reprogramming (reflash).
- Digital Wrench diagnostic functions and reference information.
- Instrument cluster diagnostic trouble code display and EFI troubleshooting.
PVT Clutch & Drive Belt System
- Polaris Variable Transmission (PVT) system operation and component descriptions.
- Drive clutch and driven clutch operation, inspection and maintenance.
- PVT cover and air duct removal, disassembly and assembly.
- Drive belt removal, inspection, installation and break-in procedures.
- Clutch centre distance inspection and adjustment.
- Drive clutch disassembly, inspection and assembly.
- Clutch springs, shift weights, spider, rollers, pins, thrust washers and bearings.
- Movable sheave bushings, clutch clearances and component replacement.
- Driven clutch disassembly, inspection and assembly.
- PVT overheating diagnosis and clutch system troubleshooting.
Transmission & Gear Selection
- Transmission removal, installation, disassembly and assembly.
- Transmission lubrication, mounting specifications and tightening torques.
- Shift lever removal and installation, shift cable inspection and adjustment.
- Transmission gears, shafts, bearings and internal component inspection.
- Snorkel gear backlash inspection and adjustment.
- Transmission service procedures for International configurations.
- Planetary differential operation, disassembly, bushing replacement and assembly for International models.
- Transmission troubleshooting and shifting-related diagnostic procedures.
AWD, Front Gearcase & Final Drive
- All-Wheel Drive (AWD) operation, diagnosis and related drivetrain components.
- Centralized Hilliard front gearcase disassembly, inspection, assembly and installation.
- Front and rear drive shaft removal and installation.
- Constant Velocity (CV) joint inspection and inner/outer CV boot replacement.
- Propeller shaft removal and installation, universal joint disassembly and assembly.
- Front and rear bearing carrier inspection, bearing replacement and bushing servicing.
- Front and rear wheel hub exploded views and component servicing.
- Front gearcase lubrication and AWD system troubleshooting.
Steering System
- Steering system inspection and steering wheel free-play adjustment.
- Steering wheel removal and steering shaft bearing replacement.
- Tie rod end and wheel hub inspection.
- Front wheel toe alignment inspection and adjustment.
- Steering assembly exploded views and component information.
Front & Rear Suspension
- Front suspension A-arm removal and replacement.
- Front ball joint removal, inspection and installation.
- Front stabilizer bar and stabilizer linkage servicing.
- Rear suspension A-arm removal and installation.
- Rear stabilizer bar servicing.
- Shock absorber and spring removal, replacement and inspection.
- Suspension spring preload adjustment.
- Suspension assembly diagrams and component tightening specifications.
Wheels, Tyres & Chassis
- Front and rear wheel removal and installation.
- Wheel hub inspection and wheel/hub tightening torque specifications.
- Tyre condition inspection and tyre pressure adjustment.
- Drive shaft boot and wheel bearing inspection.
- Chassis and main frame assembly information.
- Vehicle body fasteners and general chassis maintenance.
Hydraulic Braking System
- Hydraulic brake system operation and service information.
- Front and rear brake system exploded views.
- Brake master cylinder and brake pedal removal and installation.
- Brake fluid replacement and hydraulic system bleeding.
- Front and rear brake pad inspection, removal and replacement.
- Brake caliper removal, disassembly, inspection and reassembly.
- Brake disc inspection, runout measurement and replacement.
- Brake burnishing procedures.
- Troubleshooting poor braking performance, squealing, vibration, overheating and brake locking conditions.
International Model Parking Brake
- Parking brake system exploded views and inspection procedures.
- Parking brake cable inspection and adjustment.
- Parking brake caliper removal, disassembly and inspection.
- Parking brake pad installation and caliper assembly.
- Parking brake disc inspection and replacement.
- International model parking brake electrical switch information.
Body, Chassis & Exterior Components
- Cab frame assembly and removal.
- Chassis and main frame exploded views.
- Side safety nets, seats, seat belts and mounting components.
- Dashboard instruments, controls and glovebox.
- Hood, front and rear bumpers, front bodywork and rear fenders.
- Rear cargo box, floor panels, rocker panels and console.
- Body panel removal and installation, rear service panel and related components.
- Decal replacement and exterior body servicing.
Electrical Equipment, Battery & Charging System
- Electrical system service precautions, component information and under-dash electrical equipment.
- Battery activation, removal, installation, charging and off-season storage.
- Battery open-circuit voltage, load testing, conductance and specific gravity tests.
- Charging system inspection, stator/alternator testing and replacement.
- Regulator/rectifier servicing and charging system diagnostic flowcharts.
- Starter motor removal and installation, starter solenoid testing and starting system troubleshooting.
- Electrical voltage drop measurements and starting system diagnostic flowcharts.
Lighting, Switches & Instrument Cluster
- Ignition switch, headlight switch, AWD/2WD switch and transmission position switch.
- International model AWD/2WD/Turf switch, turn signals, hazard lights and parking brake switch.
- Brake light switch and vehicle speed sensor testing.
- Instrument cluster operation, rider information display and diagnostic mode.
- Instrument cluster connector pinouts, removal and installation.
- Headlight adjustment, bulb replacement and headlamp housing servicing.
- Rear lights and brake light component replacement.
Electronic AWD & Differential Control
- AWD coil operation and electrical fault diagnosis.
- AWD/2WD switching system and related electrical components.
- International model rear differential solenoid operation.
- Differential solenoid circuit information and Turf Mode controls.
- Vehicle speed sensor operation and testing.
Electrical Wiring Diagrams (EWD)
- Dedicated 2012 Polaris RZR 570 electrical wiring diagrams.
- 2012 RZR 570 chassis wiring harness diagrams.
- 2012 RZR 570 cargo box wiring harness diagram.
- 2012 RZR 570 International chassis wiring harness diagrams.
- 2012 RZR 570 International cargo box wiring harness diagram.
- 2012 RZR 570 wiring harness routing diagram.
- Additional electrical system break-out diagrams covering AWD, vehicle speed sensor, cooling fan, charging system, chassis power and lighting.
- Electronic fuel injection electrical system diagram.
Electrical System Diagnostics & Troubleshooting
- EFI component testing and electronic engine management diagnostics.
- Instrument cluster fault code display and diagnostic mode.
- Charging system testing and electrical fault identification.
- Starter motor and starter solenoid testing.
- Cooling fan control circuit inspection and bypass testing.
- Vehicle speed sensor, AWD coil and differential solenoid electrical diagnostics.
- Electrical system break-out diagrams and associated circuit reference information.
2013 Owner's Manual
- Introduction and vehicle safety information.
- Vehicle features, instruments and operating controls.
- Vehicle operation and driving procedures.
- Emission control system information.
- Routine maintenance and owner service procedures.
- Vehicle specifications and troubleshooting.
- Warranty information, maintenance log and reference index.
Technical Reference Data & Special Tools
- Engine mechanical specifications, tightening sequences and service limits.
- Engine timing, valve clearance and valve shim selection references.
- PVT clutch, transmission, drivetrain and chassis tightening specifications.
- Brake, steering and suspension service data.
- Special workshop tools and mechanical repair procedures.
- Electrical diagnostic procedures, wiring diagrams and technical reference charts.
Real-World Diagnostic Scenarios
In many real-world repair cases, side-by-side owners tear into their dashboard switches when the front wheels refuse to pull, completely missing the mechanical root of the problem. A mechanically binding armature plate or worn rollers in the Centralized Hilliard gearcase can actually prevent the AWD coil from generating the required magnetic field. What looks like an electrical failure on the surface is actually a mechanical fault deep inside the drivetrain components.
Diagnosing faults in this UTV without accurate data often leads to costly misdirection. For instance, when the 570 engine idles poorly, it’s incredibly easy to blame the fuel injectors or jump straight into OBD2 sensor diagnostics. However, a common issue technicians encounter is mechanical valve lash falling out of spec. When the valves tighten up, engine vacuum characteristics change drastically. As a result, the T-MAP (Temperature/Manifold Absolute Pressure) sensor reads this mechanical anomaly and sends erratic voltage data back to the ECU. If you don't know the exact factory mechanical clearance tolerances provided in this guide, you might end up replacing perfectly good electrical sensors.
Engineering Breakdown: ProStar Powertrain & EFI
This technical document goes far beyond basic maintenance. It serves as a complete engine teardown guide, walking you through every phase of cylinder head removal, camshaft timing, and crankcase separation. But modern engines don't run on mechanics alone.
The Polaris Electronic Fuel Injection system is highly integrated with the physical engine. Inside this manual, you will find targeted procedures for testing the Crankshaft Position Sensor (CPS), Throttle Position Sensor (TPS), and Idle Air Control (IAC) valve. Vibration and heat are the ultimate enemies of side-by-side electronics. We frequently see wiring circuits chafing against the chassis or hot exhaust components after a harsh trail ride. To combat this, the manual provides essential factory wiring schematics and connector pinouts to help you perform a proper Ranger RZR 570 parasitic draw diagnosis or trace a dead short. Even complex data networks, like the diagnostic communication lines linking the ECU to the Digital Wrench software, are fully mapped out.
Why Accurate Workshop Data Matters
Let’s face it, tearing down a CVT without knowing the exact clutch center distance is just asking for premature belt failure. One frequent diagnostic mistake is ignoring proper tightening sequences when reassembling the transmission cases. Applying incorrect torque to these mechanical assemblies can warp aluminum housings, leading to massive oil leaks or internal gear binding.
By having the OEM service instructions on hand, you ensure that every bolt is torqued correctly and every harness is routed safely away from moving parts. You aren't just fixing the immediate symptom; you are restoring the vehicle's long-term reliability.
Digital Document Features
This mechanical and electrical repair PDF is designed for shop floor efficiency.
- Searchable Text: Quickly find specific fault codes or part specifications.
- High-Resolution Diagrams: Zoom in on intricate cargo box harness routing without losing clarity.
- Device Friendly: Read it on your laptop, tablet, or smartphone right next to the vehicle.
- Bonus Material: Includes the original 2013 Owners Manual for quick operational reference.
Shop Floor Access & Secure Delivery
Waiting for a physical book to ship means your bay is tied up for days. Get instant access to the files you need right now.
- Flexible Payment: We accept Credit Card, PayPal, Google Pay, and Apple Pay through our secure checkout.
- Instant Access: Your download link is sent to your email immediately upon payment and remains available in your customer account.
- Download Limits: The link is valid for 10 days or up to 10 downloads, ensuring you have plenty of time to save it to your local devices.
- Reliable Backup: Having trouble with the file size? Contact us for a secure Dropbox alternative link.
- Need help downloading?: Watch our quick video tutorial here: https://servicemanuals.info/How-to-Download.mp4
Stop relying on forum rumors. Download the service manual PDF today and get wiring diagrams instantly to finish the job right.
Technical Support FAQ
How detailed is the Centralized Hilliard gearcase breakdown?
Incredibly detailed. The manual provides a full exploded view, AWD diagnosis flowcharts, and step-by-step disassembly instructions for the planetary differential, ensuring you can inspect the armature plate and rollers correctly.
Can this resource help me track down an intermittent battery drain?
Yes. It includes specific testing procedures for the charging system—including the stator and regulator/rectifier—as well as step-by-step methods for isolating a parasitic draw across the main chassis harness.
Are the wiring diagrams clear enough to read on a mobile phone?
Absolutely. The PDF is high-resolution, meaning you can zoom in on specific color-coded wires and connector pinouts without the image pixelating, making it ideal for tablet or phone use at the vehicle.
What happens if my shop WiFi drops while I download the manual?
Your access link allows for up to 10 download attempts over a 10-day period. If your connection drops, simply click the link again once your internet stabilizes to restart the process.
Does this cover engine timing and valve adjustments?
Yes. The engine section details top-dead-center (TDC) positioning, camshaft installation timing, and provides a comprehensive intake/exhaust valve lash shim selection matrix for precise mechanical tuning.