• -$10.00
Yamaha WaveRunner FX Hight Output and Cruiser - Service, Wiring & Owner Manuals
search
  • Yamaha WaveRunner FX Hight Output and Cruiser - Service, Wiring & Owner Manuals

Yamaha WaveRunner FX Hight Output and Cruiser - Service, Wiring & Owner Manuals

$29.95
$19.95 Save $10.00
No tax
Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

Yamaha WaveRunner FX Hight Output and Cruiser — Service, Wiring & Owner Manuals

This download includes watercraft maintenance/repair sections, wiring diagram and owner handbook for Yamaha WaveRunner FX Hight Output and Cruiser. The complete original technical index follows in the original order. The listed topics do not imply extra repair instructions or documents.

Selected original index topics: Wiring diagram; Chapter 7 Electrical system; OWNERS MANUAL.

Original technical index

  • SERVICE MANUAL
  • - Important information
  • - Chapter 1 General information
  • - How-use this manual
  • - Manual format
  • - Symbols
  • - Abbreviation
  • - Grease table
  • - Safety while working
  • - Fire prevention
  • - Ventilation
  • - Self-protection
  • - Parts, lubricants, and sealants
  • - Good working practices
  • - Disassembly and assembly
  • - Identification number
  • - Primary l.D. number
  • - Engine serial number
  • - Jet pump unit serial number
  • - Hull identification number (H.l.N.)
  • - Special service tool
  • - Measuring
  • - Removal and installation
  • - Feature and benefit
  • - Watercraft overview
  • - Engine overview
  • - Air filter case and air filter element
  • - Supercharger assembly
  • - Air cooler assembly
  • - Intake system
  • - Electronic control throttle valve (ETV) system
  • - Cylinder head assembly
  • - Hydraulic timing chain tensioner
  • - Ignition coil
  • - Piston and connecting rod
  • - Cylinder block and crankcase
  • - Knock sensor
  • - Lubrication system
  • - Oil pump assembly
  • - Oil pan
  • - Oil separator tank
  • - Oil cooler assembly
  • - Oil filter
  • - Exhaust system
  • - Cooling system
  • - Water cooled rectifier regulator
  • - In-tank fuel pump module
  • - Large intermediate housing and oil seal
  • - Intake grate
  • - Reverse gate assembly
  • - QSTS
  • - Multifunction meter
  • - Right multifunction display
  • - Average speed, tripmeter, and trip time measurements
  • - Electrical system
  • - Yamaha diagnostic system (YDIS)
  • - Cruise assist and no-wake mode
  • - Slant detection switch
  • - Off-throttle steering (OTS) system
  • - L-MODE (low-rpm mode) and Yamaha Security System
  • - Remote control transmitter
  • - Technical tips
  • - Engine control
  • - Cruise assist control
  • - No-wake mode control
  • - Reverse with traction control
  • - Idle speed control
  • - Over revolution control
  • - L-MODE (low-rpm mode) control
  • - Slant detection control
  • - High intake air pressure control
  • - Knock control
  • - Off-throttle steering (OTS) control
  • - Remote control transmitter control
  • - Warning control
  • - Overheat warning control
  • - Oil pressure warning contr
  • - ETV failure control
  • - Cam position sensor failure control
  • - Battery disconnection warning
  • - Fail-safe function table
  • - Chapter 2 Specification
  • - General specification
  • - Maintenance specifications
  • - Engine
  • - Jet pump unit
  • - Hull and hood
  • - Electrical
  • - Tightening torques
  • - Specified torques
  • - General torque
  • - Cable and hose routing
  • - Starboard bow view
  • - Top view
  • - Port view
  • - Chapter 3 Periodic check and adjustment
  • - Maintenance interval chart
  • - Periodic service
  • - Control system
  • - Steering system check
  • - Jet thrust nozzle steering angle check and adjustment
  • - Jet thrust nozzle QSTS angle check and adjustment
  • - Throttle lever free play check and adjustment
  • - Trolling speed check
  • - Shift cable check and adjustment
  • - Fuel system
  • - Fuel line check
  • - Water separator check
  • - Power unit
  • - Valve clearance measurement
  • - Compression pressure measurement
  • - Engine oil level check
  • - Engine oil change
  • - Oil filter replacement
  • - Air filter element check
  • - Spark plug check
  • - Electrical
  • - Battery check
  • - Jet pump unit
  • - Jet pump unit check
  • - Bilge pump
  • - Bilge strainer check
  • - Electric bilge pump strainer check
  • - General
  • - Drain plug check
  • - Throttle valve and engine internal components
  • - Lubrication points
  • - Chapter 4 Fuel system
  • - Fuel tank, fuel pump module, and fuel hose
  • - Fuel tank removal
  • - Fuel hose disconnection
  • - Fuel pump module removal
  • - Fuel sender removal
  • - Rollover valve check
  • - Check valve check
  • - Fuel line check
  • - Fuel pump module check
  • - Fuel filler neck and hose check
  • - Fuel tank check
  • - Fuel injector check
  • - Fuel injector installation
  • - Fuel sender installation
  • - Fuel pump module installation
  • - Fuel hose connection
  • - Fuel pressure measurement
  • - Chapter 5 Power unit
  • - Engine unit
  • - Engine unit removal 1
  • - Engine unit removal 2
  • - Engine unit removal 3
  • - Engine unit removal 4
  • - Engine mount removal
  • - Engine unit removal
  • - Breather assembly check
  • - Engine mount check
  • - Engine unit installation
  • - Muffler
  • - Muffler disassembly
  • - Exhaust pipe 3 removal
  • - Muffler check
  • - Pipe check
  • - Thermo sensor check
  • - Exhaust pipe 3 installation
  • - Electrical box and starter motor
  • - Electrical box and starter motor removal
  • - Air cooler, supercharger, and throttle body assembly
  • - Air cooler and supercharger removal
  • - Intake assembly removal
  • - Intake disassembly
  • - Air cooler check
  • - Supercharger check
  • - Throttle body assembly check
  • - Intake manifold check
  • - Intake manifold installation
  • - Supercharger installation
  • - Air cooler intake hose installation
  • - Boost pipe installation
  • - Oil cooler, oil pump assembly, and drive gear
  • - Oil cooler and oil pump assembly removal
  • - Drive gear removal
  • - Drive gear assembly removal
  • - Drive gear disassembly
  • - Oil cooler assembly check
  • - Oil pump assembly check
  • - Idle gear check
  • - Drive gear check
  • - Drive gear clutch check
  • - Oil pump drive gear assembly
  • - Drive gear assembly installation
  • - Oil pump assembly installation
  • - Camshaft
  • - Cylinder head cover removal
  • - Camshaft and timing chain removal
  • - Camshaft removal
  • - Camshaft check
  • - Camshaft sprocket check
  • - Timing chain check
  • - Timing chain tensioner check
  • - Camshaft installation
  • - Cylinder head cover installation
  • - Valve clearance adjustment
  • - Cylinder head
  • - Cylinder head assembly removal
  • - Cylinder head disassembly
  • - Cylinder head assembly removal
  • - Valve removal
  • - Cylinder head check
  • - Valve spring check
  • - Valve check
  • - Valve guide check
  • - Valve guide removal
  • - Valve guide installation
  • - Valve seat check
  • - Valve seat refacing
  • - Valve installation
  • - Cylinder head installation
  • - Generator cover and flywheel magneto
  • - Generator cover and flywheel magneto removal
  • - Generator cover disassembly
  • - Drive coupling removal
  • - Flywheel magneto removal
  • - Bearing removal
  • - Idle gear and shaft check
  • - Transfer shaft check
  • - Starter clutch check
  • - Bearing installation
  • - Oil seal installation
  • - Generator cover assembly
  • - Flywheel magneto installation
  • - Drive coupling installation
  • - Oil separator tank and oil pan
  • - Oil separator tank and oil pan removal
  • - Oil pan disassembly
  • - Oil pan check
  • - Crankcase, connecting rod, and piston
  • - Crankcase, connecting rod, and piston disassembly
  • - Crankcase disassembly
  • - Connecting rod and piston removal
  • - Crankcase check
  • - Anode check
  • - Piston check
  • - Piston ring check
  • - Piston pin check
  • - Connecting rod check
  • - Cylinder check
  • - Crankshaft check
  • - Crankshaft pin oil clearance check
  • - Crankshaft journal oil clearance check
  • - Connecting rod and piston installation
  • - Crankcase assembly
  • - Cooling water
  • - Cooling water hose routing
  • - Thermostat removal
  • - Cooling water line check
  • - Thermostat check
  • - Chapter 6 Jet pump unit
  • - Intake grate and ride plate
  • - Intake grate and ride plate removal
  • - Jet pump unit
  • - Jet pump unit removal
  • - Jet pump unit removal
  • - Jet pump unit installation
  • - Reverse gate
  • - Reverse gate removal
  • - Jet thrust nozzle and nozzle ring
  • - Jet thrust nozzle and nozzle ring removal
  • - Impeller duct and impeller housing
  • - Impeller duct and impeller housing removal
  • - Impeller duct and drive shaft
  • - Impeller duct and drive shaft disassembly
  • - Drive shaft removal
  • - Impeller check
  • - Impeller housing check
  • - Drive shaft check
  • - Drive shaft installation
  • - Impeller duct and impeller housing installation
  • - Transom plate and hoses
  • - Transom plate and hose removal
  • - Water hose check
  • - Transom plate installation
  • - Intermediate housing
  • - Intermediate housing removal
  • - Intermediate housing disassembly
  • - Intermediate housing removal
  • - Driven coupling removal
  • - Intermediate drive shaft removal
  • - Oil seal removal
  • - Bearing removal
  • - Intermediate drive shaft and grease hose check
  • - Driven coupling and intermediate housing check
  • - Bearing installation
  • - Oil seal installation
  • - Driven coupling installation
  • - Intermediate housing installation
  • - Chapter 7 Electrical system
  • - Electrical components
  • - Electrical box
  • - Electrical components
  • - Electrical box disassembly
  • - Fuse box disassembly
  • - Electrical analysis
  • - Check using the YDIS
  • - Input voltage measurement
  • - Peak voltage measurement
  • - Ignition system
  • - Ignition coil
  • - Pickup coil
  • - Charging system
  • - Stator coil
  • - Rectifier regulator
  • - Control system
  • - Oil pressure switch
  • - Thermoswitch
  • - Thermo sensor
  • - Engine temperature sensor
  • - Intake air temperature sensor
  • - Intake air pressure sensor
  • - Knock sensor
  • - Throttle position sensor
  • - Accelerator position sensor
  • - Electronic throttle valve relay
  • - Cam position sensor
  • - Slant detection switch
  • - Steering sensor
  • - Reverse sensor
  • - Right handlebar switch assembly
  • - ECM circuit
  • - Earth plate
  • - Electric bilge pump
  • - Fuel system
  • - Fuel injector
  • - Fuel pump module
  • - Starting system
  • - Fuse
  • - Left handlebar switch assembly
  • - Main and fuel pump relay
  • - Starter relay
  • - Starter motor
  • - Starter motor disassembly
  • - Starter motor operation
  • - Armature
  • - Brush holder
  • - Gear cover
  • - Rear cover
  • - Starter motor assembly
  • - Remote control system
  • - Transmitter registration
  • - Remote control transmitter
  • - Remote control receiver
  • - Indication system
  • - Multifunction meter
  • - Operation button assembly
  • - Compass display
  • - Air temperature display
  • - Water temperature display
  • - Speed sensor
  • - Digital speedometer display
  • - Digital speedometer display
  • - Fuel level meter display and fuel level warning indicator
  • - Check engine warning indicator
  • - Diagnostic display
  • - Oil pressure warning indicator
  • - Engine overheat warning indicator
  • - Buzzer
  • - Chapter 8 Hull and hood
  • - Handlebar
  • - Steering pad removal
  • - Steering pad removal
  • - Handlebar holder removal
  • - Handlebar assembly removal
  • - Left and right handlebar switch disassembly
  • - Handlebar check
  • - Handlebar switch assembly check
  • - Handlebar assembly installation
  • - QSTS grip and converter
  • - QSTS grip and converter disassembly
  • - QSTS cable removal
  • - QSTS check
  • - QSTS cable installation
  • - Front hood
  • - Front hood removal
  • - Damper check
  • - Mirror disassembly
  • - Mirror assembly installation
  • - Rivet removal
  • - Rivet installation
  • - Steering console cover
  • - Multifunction meter and cover removal
  • - Side cover removal
  • - Center cover removal
  • - Center cover disassembly
  • - Side cover removal
  • - Shift lever removal
  • - Steering master
  • - Steering master removal
  • - Steering master disassembly
  • - Steering master component check
  • - Spring installation
  • - Rubber seal installation
  • - Remote control cables and speed sensor lead
  • - Remote control cables and speed sensor lead removal
  • - Steering cable installation (steering master end)
  • - Steering cable installation (jet pump end)
  • - Shift cable installation (shift lever end)
  • - Shift cable installation (jet pump end)
  • - Hoses
  • - Hose removal
  • - Seats and hand grip
  • - Seat and hand grip removal
  • - Seat lock check
  • - Exhaust system
  • - Exhaust system and battery removal
  • - Exhaust system check
  • - Deck and hull
  • - Deck and hull disassembly 1
  • - Deck and hull disassembly 2
  • - Drain plug check
  • - Front protector 1 installation
  • - Pull-up cleat cover installation
  • - Reboarding step installation
  • - Chapter 9 Trouble analysis
  • - YDIS
  • - Introduction
  • - Features
  • - Functions
  • - Contents
  • - Operating
  • - Connecting the communication cable-the watercraft
  • - Engine unit trouble analysis
  • - Using the YDIS for engine unit trouble analysis
  • - Self-diagnosis
  • - Diagnostic code table
  • - Diagnostic code and checking step
  • - Engine unit trouble analysis (diagnostic code not detected)
  • - Trouble analysis chart
  • - Wiring diagram
  • OWNERS MANUAL
  • - Important manual information
  • - Table of contents
  • - General and important labels
  • - Identification numbers
  • - Primary Identification (PRI-ID) number
  • - Hull Identification Number (HIN)
  • - Engine serial number
  • - Emission control information
  • - Approval label of emission control certificate
  • - Manufactured date label
  • - Star labels
  • - Important labels
  • - Warning labels
  • - Other labels
  • - Safety information
  • - Limitations on who may operate the watercraft
  • - Cruising limitations
  • - Operation requirements
  • - Recommended equipment
  • - Hazard information
  • - Watercraft characteristics
  • - Water-skiing
  • - Rules of the Road
  • - To get more boating safety information
  • - Enjoy your watercraft responsibly
  • - Features and functions
  • - Location of main components
  • - Front view
  • - Rear view
  • - Control system
  • - Engine compartment
  • - Operation of controls and other functions
  • - Seats
  • - Hood
  • - Fuel tank filler cap
  • - Remote control transmitter
  • - Engine stop switch
  • - Engine shut-off switch
  • - Start switch
  • - Right handlebar switches
  • - Throttle lever
  • - Cooling water pilot outlets
  • - Steering system
  • - Tilt lever
  • - Shift lever
  • - Quick Shift Trim System (QSTS) selector
  • - Handgrip
  • - Reboarding step
  • - Bow eye
  • - Stern eyes
  • - Yamaha Engine Management System (YEMS)
  • - Yamaha Security System
  • - Yamaha Security System settings
  • - No-wake mode
  • - Cruise assist
  • - Multifunction information center
  • - Storage compartments
  • - Operation
  • - Fuel and oil
  • - Gasoline
  • - Engine oil
  • - Filling the fuel tank
  • - Pre-operation checks
  • - Pre-operation check list
  • - Pre-operation check points
  • - Engine compartment
  • - Hull and deck
  • - Fuel level
  • - Engine oil level
  • - Water separator
  • - Bilge
  • - Stern drain plugs
  • - Battery
  • - Fire extinguisher
  • - Throttle lever
  • - Steering system
  • - Shift lever and reverse gate
  • - Quick Shift Trim System (QSTS)
  • - Jet intake
  • - Engine shut-off cord
  • - Switches
  • - Multifunction information center
  • - Operation
  • - Engine break-in
  • - Launching the watercraft
  • - Stopping the engine
  • - Leaving the watercraft
  • - Operating your watercraft
  • - Getting-know your watercraft
  • - Learning-operate your watercraft
  • - Riding with passengers
  • - Starting the watercraft
  • - Boarding and starting in shallow water
  • - Boarding and starting from a dock
  • - Boarding and starting from a dock
  • - Boarding and starting in deep water
  • - Boarding alone
  • - Boarding with passengers
  • - Capsized watercraft
  • - Turning the watercraft
  • - Stopping the watercraft
  • - Beaching the watercraft
  • - Docking the watercraft
  • - Reverse on waterways
  • - Rough water operation
  • - Post-operation care
  • - Transporting
  • - Maintenance and care
  • - Storage
  • - Flushing the cooling system
  • - Lubrication
  • - Fuel system
  • - Battery
  • - Cleaning the watercraft
  • - Maintenance and adjustments
  • - Owner's/operator's manual and tool kit
  • - Periodic maintenance chart
  • - Checking the fuel system
  • - Fuel tank
  • - Engine oil and oil filter
  • - Air filter element
  • - Checking the jet thrust nozzle angle
  • - Checking the shift cable
  • - Checking and adjusting the throttle cable
  • - Cleaning and adjusting the spark plugs
  • - Lubrication points
  • - Checking the battery
  • - Fuel injection system
  • - Specifications
  • - Specifications
  • - Trouble recovery
  • - Troubleshooting
  • - Troubleshooting chart
  • - Emergency procedures
  • - Cleaning the jet intake and impeller
  • - Jumping the battery
  • - Replacing the fuses
  • - Towing the watercraft
  • - Submerged watercraft
  • - Consumer information
  • - Limited warranty