2009 Index
General Information & Scheduled Maintenance
- Workshop safety procedures, motorcycle servicing instructions, cleaning methods, and repair practices.
- Periodic maintenance schedule, fuel requirements, engine lubrication, and winter lubrication recommendations.
- Engine oil and filter replacement, primary chaincase lubricant, and transmission oil servicing.
- Inspection and adjustment of critical fasteners, clutch, brakes, suspension, steering, and engine mounts.
- Motorcycle storage and return-to-service procedures.
Engine Mechanical & Overhaul
- Engine specifications, component wear limits, tightening torques, and mechanical repair procedures.
- Engine removal and installation, including preparation of the motorcycle for workshop service.
- Top-end and bottom-end engine overhaul, with procedures for engines installed in or removed from the chassis.
- Engine disassembly, component inspection, cleaning, repair, and reassembly.
Cylinder Heads, Valves & Rocker Arms
- Cylinder head removal, disassembly, inspection, and reassembly.
- Valve guide replacement, valve, and seat refacing.
- Rocker arm support plates, push rods, hydraulic lifters, and associated covers.
- Cylinder head and valve train servicing during top-end engine overhaul.
Cylinders, Pistons & Crankcase
- Cylinder removal, inspection, deglazing, boring, and honing.
- Piston disassembly, cleaning, inspection, and reassembly.
- Crankcase separation and assembly, including left and right crankcase halves.
- Flywheel and connecting rod inspection, cylinder studs, bearings, and associated components.
Camshafts & Engine Lubrication System
- Camshafts, cam support plate, cam needle bearings, and oil pressure relief valve.
- Engine oil flow through the top and bottom ends, oil return, and crankcase breather operation.
- Oil pump operation, removal, inspection, and installation.
- Engine oil pressure testing and oil pressure indicator system.
- Engine oil pan and associated lubrication components.
Engine Troubleshooting & Mechanical Diagnosis
- Engine compression and cylinder leakdown testing.
- Diagnosis of valve train noise, engine smoke, and excessive oil consumption.
- Engine mechanical inspection and troubleshooting procedures.
Electronic Fuel Injection (EFI)
- Electronic Fuel Injection (EFI) system specifications and troubleshooting.
- Fuel tank, fuel filter, fuel pressure regulator, fuel level sender, and fuel pump.
- Fuel injector removal and installation, fuel pressure testing, and intake leakage inspection.
- Induction module and associated engine management components.
Electronic Throttle & Engine Sensors
- Twist Grip Sensor and associated jumper harness.
- Throttle Control Actuator (TCA) and electronic throttle components.
- Engine Temperature (ET) sensor and Temperature Manifold Absolute Pressure (TMAP) sensor.
- Oxygen (O2) sensors and associated fuel injection equipment.
Air Intake, Exhaust & Emission Control
- Air cleaner assembly removal and installation.
- Exhaust system and muffler removal, installation, and leakage inspection.
- Active Exhaust (HDI): exhaust valve actuator, actuator cable, and active exhaust valve.
- Evaporative emissions control equipment for California (CA) models, including charcoal canister, purge solenoid, vapour valve, and associated tubing.
Primary Drive, Clutch & Final Belt Drive
- Primary chaincase cover and housing removal, inspection, and installation.
- Primary drive components, mainshaft bearing, seals, and shifter shaft bushings.
- Clutch assembly, clutch pack, and clutch bearing replacement.
- Transmission sprocket servicing and rear drive belt removal, installation, and adjustment.
- Rear belt deflection measurement, sprocket inspection, and final drive maintenance.
Transmission & Gearshift Mechanism
- Transmission technical specifications, power flow, and service wear limits.
- Transmission assembly removal, disassembly, inspection, overhaul, and installation.
- Main drive gear, bearings, and mainshaft seal replacement.
- Transmission case disassembly and reassembly.
- Shifter linkage, shifter rod, and clutch release cover servicing.
Front & Rear Wheels
- Front and rear wheel removal, inspection, and installation.
- Sealed wheel bearing inspection and replacement.
- Wheel rim runout measurement and wheel balancing-related inspections.
- Spoked wheel assembly and truing procedures for 16-inch front/rear rims and 17-inch rims.
- Rear wheel compensator, isolator, and sprocket bearing replacement.
Front Suspension & Steering
- Front fork removal, disassembly, inspection, reassembly, and installation.
- Front fork oil replacement and suspension servicing.
- Steering head bearing removal, inspection, lubrication, and adjustment.
- Handlebar removal, installation, and adjustment, including grips and rubber mounts.
Rear Suspension & Swingarm
- Rear air suspension inspection and air leakage testing.
- Rear shock absorber removal, inspection, disassembly, and installation.
- Rear fork/swingarm removal, assembly, and installation.
- Suspension adjustment and maintenance procedures.
Front & Rear Brake Systems
- Front and rear brake master cylinder removal, disassembly, inspection, and assembly.
- Front and rear brake calliper servicing.
- Brake pad and brake disc inspection and replacement.
- Hydraulic brake fluid inspection, replacement, and brake system bleeding.
- Service information for brake lines on models without ABS.
Anti-Lock Braking System (ABS)
- Dedicated ABS service section covering ABS module removal and installation.
- Front and rear wheel speed sensors.
- Hydraulic brake lines between тера the master cylinders, ABS module, and brake callipers.
- ABS system component servicing for applicable equipped models.
Electrical System & Electronic Control
- Electrical system specifications, service procedures, and tightening torques.
- Electronic Control Module (ECM), ignition coil, and voltage regulator.
- Main fuse, fuse holders, fuse blocks, and electrical relays.
- Electrical component mounting trays, battery tray, and related equipment.
- Turn Signal Module / Hands-Free Security Module (TSM/HFSM) and security siren.
Starting & Charging Systems
- Starter motor removal, inspection, and installation.
- Starter solenoid, field coil, starter drive, plunger, and electrical contacts.
- Alternator removal, cleaning, inspection, and installation.
- Battery inspection, charging, and voltage testing.
Engine & Vehicle Electrical Sensors
- Crankshaft Position Sensor (CKP).
- Vehicle Speed Sensor (VSS) and neutral switch.
- Oil pressure switch and sender.
- Front and rear stoplight switches.
- Electrical component inspection and associated service procedures.
Headlights, Auxiliary Lamps & Exterior Lighting
- Main headlamp servicing, including separate procedures for FLTR and other Touring configurations.
- Auxiliary lamps, mounting brackets, and headlamp alignment.
- Tail lamp, front and rear turn signals, and fender tip lamps.
- Rear fender lighting harnesses and associated electrical components.
- Tour-Pak lighting equipment and associated wiring.
Instrument Cluster & Dashboard Controls
- Speedometer, tachometer, and indicator lamps.
- Fuel level, ambient air temperature, voltmeter, and oil pressure gauges where fitted.
- Instrumentation differences for FLHX, FLHT/C/U, FLTR, and FLHR/C configurations.
- Ignition/light key switch, fork lock, fairing switches, and instrument nacelle controls.
Audio, Radio & Communication Systems
- Advanced Audio System components, radio equipment, and speakers.
- Front and rear headset connections, rear passenger controls, and CB module.
- Radio antenna cable, CB antenna cable, and audio system harness servicing.
- Model-specific audio equipment for applicable Touring configurations.
Main Wiring Harnesses & Electrical Connectors
- Main wiring harness removal and installation, including model-specific procedures.
- Electrical interconnect harnesses, wiring troughs, and accessory connections.
- Handlebar switch assembly disassembly, repair, and installation.
- Electrical connector identification and connector location references.
Electrical Wiring Diagrams — 2009 Touring Models
- Dedicated 2009 Harley-Davidson Touring electrical wiring diagrams.
- Wiring diagram reference information and connector location documentation.
- Electrical wiring and harness reference material accompanying the workshop service sections.
Electrical Connector & Terminal Repair
- Repair procedures for AMP Multilock, Autofuse, Delphi, Deutsch, and Molex connectors.
- Packard Metri-Pack 150, 280, 480, and 630 electrical connectors.
- Packard Micro-64 connectors and Delphi 73-terminal ECM connector.
- Deutsch standard, mini, and solid-barrel terminals.
- Terminal crimping, sealed splice repair, and fuse block connector servicing.
Fairings, Windshields & Body Components
- Upper and lower fairings, inner fairings, windshields, and fairing caps.
- Fairing and instrument nacelle components for FLTR, FLHX, and FLHT/C/U models.
- Headlamp nacelle and windshield assemblies for FLHR/C models.
- Air deflectors, front and rear fenders, rear fascia, and engine guards.
- Model-specific body component removal and installation procedures.
Seats, Saddlebags & Touring Accessories
- Seat removal, installation, and mounting components for the various Touring configurations.
- Saddlebags, mounting hardware, and support rails.
- Tour-Pak: removal, installation, adjustment, hinges, locks, and latches.
- Tour-Pak luggage rack, passenger backrest, lighting, and speaker equipment.
- Footboards, footrests, side stand, and related mounting components.
Chassis & Model-Specific Service Information
- Chassis specifications, Vehicle Identification Number (VIN), and identification information.
- Service procedures for FLHT, FLHTC/U, FLTR, FLHX, and FLHR/C Touring model configurations.
- Front engine mounting, rear frame components, and associated chassis hardware.
- Model-specific differences in bodywork, instruments, lighting, and accessory equipment.
Technical Specifications, Special Tools & Reference Data
- Engine, chassis, fuel system, transmission, and electrical system specifications.
- Service wear limits, component inspection data, and tightening torque values.
- Workshop special tools and repair equipment.
- Metric, fluid capacity, and torque conversion tables.
- Technical glossary, acronyms, and abbreviations.
Real-World Workshop Scenarios
A common issue technicians encounter on this specific platform is an erratic idle or a forced limp-mode condition. During troubleshooting, it is easy to assume the Throttle Control Actuator (TCA) is failing. In many real-world repair cases, the actual fault is mechanical fretting within the Twist Grip Sensor (TGS) jumper harness located inside the handlebars. If the internal wire routing was stressed during a handlebar swap, normal road vibration causes micro-voltage drops across the connector pins. The ECM misinterprets this physical wear as a critical sensor failure.
Using this Harley Davidson Touring Models Service & Repair Manual 2009, you gain access to the precise voltage tests and connector pinouts needed to prove out the circuit. By cross-referencing the extensive Appendix A on terminal repair, you can re-pin the damaged Molex or Delphi connectors instead of throwing an expensive throttle body at a simple wiring issue.
Advanced System Integration
By this production year, the dividing line between mechanical components and electrical regulation had permanently blurred. The Anti-lock Braking System (ABS) on these heavy cruisers perfectly illustrates this. We often see bikes arrive with flashing ABS lamps after a routine tire change. One frequent diagnostic mistake is condemning the ABS module or assuming a complex data failure. The real culprit is usually mechanical.
If a mechanic ignores the factory installation procedures for the sealed wheel bearings, the wheel speed sensor can be crushed, misaligned, or pushed out of its required air gap. The ABS module sees this mechanical error as an open electrical circuit. This manual outlines the strict front and rear wheel lacing limits, radial runout checks, and axle torque specifications so your mechanical foundation properly supports the electronic control systems and complex CAN-bus communication networks seamlessly.
Engine & Powertrain Teardown
Diving into the Twin Cam powertrain requires absolute precision. When you are pulling the rocker arm support plates, deglazing a cylinder, or addressing the oil pressure relief valve, relying on "close enough" estimates will strip aluminum crankcase threads or cause catastrophic top-end oil starvation. This engine teardown guide covers everything from splitting the case halves to checking flywheel runout and replacing the mainshaft bearing inner race.
Furthermore, isolated faults often trigger secondary driveline damage. For example, a worn rear wheel compensator isolator creates severe driveline lash. This harsh mechanical shock transmits straight into the transmission main drive gear, eventually destroying the lip seal and causing a stubborn fluid leak. Access to genuine OEM service instructions ensures you apply the correct tightening sequences and torque specifications across all mechanical assemblies, neutralizing vibration before it compromises adjacent systems.
Workshop Relevance & Diagnostic Authority
Attempting a 2009 Harley Touring parasitic draw diagnosis on a model loaded with an Advanced Audio System, CB module, and HFSM (Hands-Free Security Module) without accurate maps is a massive waste of billable hours. This technical document arms you with complete wiring circuits, primary fuse box layouts, and interconnect harness routing paths.
Because the resource includes deep-dive electrical caddy breakdowns alongside heavy mechanical procedures, you can trace a fault from a blown main fuse directly back to a pinched wire beneath the Tour-Pak luggage rack. The searchable format allows you to rapidly jump between the fuel injection (EFI) induction module specs and the TMAP sensor diagnostics without flipping through greasy paper pages.
Technical PDF Features
- Fully Searchable Text: Find exact codes, connector types, or torque values in seconds.
- High-Resolution Diagrams: Zoom in on dense ABS brake line routing and intricate wiring diagrams without pixelation.
- Complete Coverage: Encompasses all variations including FLHT/C/U, FLTR, FLHR/C, and FLHX models.
- Device Friendly: Formatted to work flawlessly on shop tough-books, iPads, and smartphones.
Shop Floor Access Guarantee
Your bay is tied up, and you need this data ten minutes ago. We understand shop pacing. Secure your mechanical and electrical repair PDF using Apple Pay, Google Pay, PayPal, or any major Credit Card. As soon as your checkout clears, a secure download link is dispatched to your email and permanently logged in your customer account.
You have a flexible 10-day window or up to 10 downloads to save the file locally to your hard drive. If your shop Wi-Fi drops or you hit a technical snag, our support team can deploy a backup delivery via Dropbox to keep your project moving forward.
Need a quick visual on the download process? Check out our brief tutorial: https://servicemanuals.info/How-to-Download.mp4
Access the full PDF guide now and eliminate guesswork in your repairs.
Practical Diagnostic Use Cases (FAQs)
What causes the engine to throw a TCA code after installing aftermarket handlebars?
In practical diagnostics, this is almost always a mechanical stress failure applied to an electrical component. Pulling wires aggressively through sharp handlebar angles damages the Twist Grip Sensor jumper harness. The manual provides the exact Molex and Deutsch connector testing protocols to verify pin integrity before you assume the Throttle Control Actuator is actually dead.
Are the procedures for the FLHTCU Advanced Audio System and CB antenna included?
Yes. The document features a comprehensive breakdown of the advanced audio system, including the front fairing speakers, passenger headset receptacles, CB module, and specific audio harness routing unique to the Ultra Classic and Road Glide platforms.
How do I isolate a leak in the rear air suspension system?
A harsh ride is often misdiagnosed as blown shock absorbers. This guide provides the dedicated "Check for Air Leaks" procedure, detailing how to properly pressure-test the air lines, valves, and shock boots to pinpoint the exact source of the pressure drop without unnecessarily replacing the main suspension units.
Does this resource cover the active exhaust system found on international models?
Yes, the technical document covers the HDI (International) Active Exhaust components. It includes removal, installation, and cable adjustment procedures for the exhaust valve actuator, ensuring proper backpressure and emission compliance.