• -$10.00
Fisker Karma Service & Repair Manual 2011 2012 PDF
search
  • Fisker Karma Service & Repair Manual 2011 2012 PDF
  • Fisker Karma Service & Repair Manual 2011 2012 PDF

Fisker Karma Service & Repair Manual 2011 2012 PDF

$29.95
$19.95 Save $10.00
No tax

Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

2011 2012 Index

General Information & Model Coverage

  • Comprehensive factory service and repair manual covering Fisker Karma vehicle models for model years 2011 through 2012.

Engine, Turbocharging & Fuel Systems

  • Engine mechanical service including mounting procedures, cylinder head gaskets, camshaft and timing cover seals, oil maintenance, thermostat, and water pump replacement.
  • Sensor and component replacement including engine control module (ECM), turbocharger boost and actuator components, MAF, coolant and ambient temperature sensors, crankshaft and camshaft position sensors, knock sensors, ignition coils, spark plugs, MAP, and oxygen sensors.
  • Fuel system coverage including fuel tanks, fuel level senders, fuel rails, injectors, pressure regulators, tank pumps, high-pressure fuel pumps, purge valves, air cleaners, intake manifolds, throttle bodies, and intercoolers (charge air coolers).
  • Exhaust system and turbocharger overhaul procedures including exhaust manifolds, catalytic converters, and muffler assemblies.

Electric Drive & High-Voltage Powertrain

  • Electric drive components including generator replacement, mounting, and shaft couplers.
  • High-voltage battery service including manual service disconnect (MSD) isolation procedures, battery assemblies, fuses, and charging port service.
  • Power electronics including AC/DC inverters, 3-phase AC inverters, and DC/DC converters.

Cooling & HVAC Systems

  • Comprehensive cooling system service including engine/cabin coolant draining/refilling, low-temp battery coolant bleeding, motor/generator/inverter cooling, auxiliary and low-temp coolant pumps, radiator packs, cooling fans, and coolant reservoirs.
  • HVAC system service covering refrigerant recovery and recharge, HVAC assemblies, air temperature, mode, and recirculation actuators, heater cores, blower motors, compressors, condensers, evaporators, expansion valves, and pollen filters.

Transmission, Driveline & Rear Drive Module (RDM)

  • Final drive and differential service including fluid draining/refilling, oil seals, halfshafts, CV joints, and gaiters.
  • Rear Drive Module (RDM) specialized service and subframe removal and installation procedures.

Suspension, Steering & Braking Systems

  • Steering system maintenance including steering wheels, steering columns, steering racks, and power steering fluid servicing and bleeding.
  • Suspension overhaul including four-wheel alignment checks, spring and shock absorber assemblies, lower arms, upper wishbones, tie rod ends, toe links, sway bars and links, hubs, and suspension uprights.
  • Brake system service including bleeding procedures, master cylinders, electronic brake control modules (EBCM), ABS sensors, brake rotors, calipers, pads, parking brake motors, cables, and park brake shoe adjustments.
  • Wheels, tires, and TPMS wheel sensor replacement.

Chassis, Body & Exterior Fittings

  • Chassis structural components including front and rear subframes, cross braces, tunnel closing panels, and high-voltage cable closing panels.
  • Body exterior service including bumpers, diffusers, charging port and fuel filler covers, fenders, hood and trunk assemblies, door hinges, latches, check straps, weatherstripping seals, and roof ditch moldings.
  • Roof and glazing procedures covering solar roof assemblies, door glass alignment, windshields, rear screens, door glass, quarter glass, and window regulators.
  • Exterior fittings including wheel arch liners, plenum covers, and mirror assemblies.

Interior Trim, Dash, Restraints & Seats

  • Dash assembly procedures including accelerator pedal position sensors, brake pedal assemblies, topper panels, center stack switch housings, and knee/dash closing panels.
  • Interior trim service including door covers, steering column cowls, carpeting, A/B/D post finishers, center consoles, gloveboxes, headlinings, rear bulkheads, and parcel shelf finishers.
  • Restraint system service including pre-tensioners, seat belts, and front, knee, curtain, and side thorax airbags.
  • Seat service including driver and rear seat assemblies, seat runners, motors, position sensors, seat control modules, and upholstery covers.

Electrical Equipment & Infotainment Systems

  • Electrical service including 12V battery isolation procedures, fuel injector harnesses, start/stop and PRND switches, hybrid control modules (HCM), vehicle control modules (VCM), parking distance control (PDC) modules, inertial measurement units (IMU), and heated seat memory modules.
  • Exterior lighting, wiper, and washer systems including headlamps, alignment procedures, CHMSL, rear lamp clusters, bumper fog and reverse lamps, wiper motors and arms, washer fluid reservoirs and pumps, and headlamp washer jets.
  • Infotainment service covering central infotainment units (CIU).

Real-World Service Challenges and Powertrain Diagnostics

Handling the delicate integration between the 2.0 L (121.9 cu in) turbocharged Ecotec engine and the twin 120 kW electric motors requires absolute precision. This is not a standard internal combustion setup where you can rely purely on mechanical intuition. For instance, the thermal management system alone utilizes three distinct cooling loops. One frequent mistake during reassembly is rushing the coolant refill for the low-temp battery or inverter circuits. A trapped air pocket here won't just trigger a warning light; it will induce thermal derating, drastically limiting power output. This technical document provides the explicit drain, refill, and bleeding procedures to prevent these easily avoidable comebacks.

During troubleshooting, technicians often chase intermittent faults in the EV drive system. Without accurate data mapping the 3-phase AC inverters and the DC/DC converter, you are essentially flying blind. This workshop reference breaks down the precise testing protocols for the Hybrid Control Module (HCM) and Vehicle Control Module (VCM), ensuring you replace the right component the first time.

RDM Removal and Structural Reassembly Precision

A common issue technicians encounter on this platform involves servicing the Rear Drive Module (RDM). Dropping the rear subframe to address an input seal leak or differential fault is a major undertaking. In many engine rebuild and drivetrain overhaul cases, mechanics reuse stretched subframe bolts or apply a standard "gut-feel" torque to the RDM mounting points. As a result, NVH (noise, vibration, and harshness) levels spike dramatically, and premature differential wear is almost guaranteed.

This model-specific guide features a dedicated 54-step RDM service procedure. It details every critical phase—from proper Loctite preparation and exact tightening sequences, to handling the High Voltage Interlock Loop (HVIL) plates safely. You get the factory tolerances needed to ensure the half-shafts and CV joints sit perfectly, minimizing the risk of accelerated wear on the drivetrain components.

Suspension Tolerances and Brake System Calibration

Because this vehicle carries significant battery mass, the suspension and braking systems are under continuous heavy load. When tackling a suspension overhaul—whether replacing the upper wishbones, swapping the rear shock absorbers, or addressing worn tie rod ends—factory clearance tolerances are strictly non-negotiable.

Furthermore, performing a mechanical tear-down of the braking system goes beyond just swapping pads and rotors. This resource outlines the exact bleed procedure for the Electronic Brake Control Module (EBCM) and the calibration steps for the electronic parking brake motor. Getting the parking brake cable adjustment wrong can lead to dragging shoes, warped rear rotors, and premature motor burnout.

Digital Utility for the Modern Workshop Bay

Flipping through a grease-stained paper book wastes time. This 158 MB digital PDF is built for shop floor efficiency. The detailed schematics, wiring harness layouts, and tear-down diagrams are high-resolution. You can zoom in on the specific pinout for the turbocharger boost pressure modulator or blow up the dashboard disassembly steps on your tablet without losing clarity. The ability to search instantly for specific OEM repair instructions keeps your hands on the tools rather than endlessly thumbing through an index.

Secure Access and Immediate Shop Floor Delivery

When a vehicle is tying up a lift, waiting for data costs you money. You can check out securely using your preferred method: Credit Card, PayPal, Google Pay, or Apple Pay. The instant access service manual download link is dispatched automatically to your email and populated in your secure customer account the moment the transaction clears.

Your secure PDF link remains active for 10 days or up to 10 downloads. If your shop laptop crashes or the file is accidentally deleted, we offer a guaranteed backup delivery via our Dropbox server. If you need any assistance retrieving your file, just watch our quick walkthrough: https://servicemanuals.info/How-to-Download.mp4

Access the full PDF guide now and eliminate guesswork in your repairs.

Practical Diagnostic Use Cases (FAQs)

I am pulling the rear subframe to service the dual motors. Does this manual detail the high-voltage disconnect sequence?
Yes. Before you even touch a subframe bolt, the guide provides the mandatory high-voltage battery isolation steps, including Manual Service Disconnect (MSD) removal and correct HVIL plate handling, ensuring complete technician safety.

Will this resource help me resolve an airlock in the battery thermal management system?
Absolutely. The 2011–2012 Fisker Karma utilizes multiple cooling systems. You will find distinct, step-by-step drain, refill, and bleed instructions for the engine coolant, the low-temp battery loop, and the dedicated motor/inverter cooling circuit.

How specific are the clearance and torque values for the Ecotec 2.0L top end?
Extremely specific. The manual delivers factory torque specifications and tightening sequences for the cylinder head, camshaft cover, timing chain setup, and exhaust manifold to ensure proper sealing under high-boost conditions.

Can I view this repair manual PDF on a diagnostic tablet in the garage?
Yes, the 158 MB file is universally compatible. Whether you are using an iPad, an Android-based shop tablet, or a ruggedized PC, you can easily open, navigate, and zoom in on all the technical illustrations and diagrams at the workbench.