• -$10.00
BMW F 650 CS Scarver - Service Manual - Manual de Taller
search
  • BMW F 650 CS Scarver - Service Manual - Manual de Taller

BMW F 650 CS Scarver - Service Manual - Manual de Taller

$29.95
$19.95 Save $10.00
No tax
Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

BMW F 650 CS Scarver - Service Manual - Manual de Taller

Digital technical documentation with sections on Activities, MAINTENANCE SCHEDULE, PRE-DELIVERY CHECK. Review the complete contents below for the systems and procedures covered.

Manual contents

  • Activities
  • MAINTENANCE SCHEDULE
  • PRE-DELIVERY CHECK
  • SERVICE DATA
  • CONTENTS
  • 00 TIGHTENING TORQUES, OPERATING FLUIDS
  • Tightening torques
  • Table of operating fluids
  • 00 PRE-DELIVERY CHECK
  • General view of crated motorcycle
  • Checking the shipping crate for damage
  • In case of damage in Germany
  • In case of damage in importer markets
  • Unpack the motorcycle
  • Inspecting motorcycle for damage
  • Checking that delivery is complete
  • Installing remaining items on motorcycle
  • Filling and charging the battery
  • Removing the battery
  • Filling and charging the battery
  • Checking engine oil level
  • Checking tyre pressures
  • Final inspection and function check
  • Final cleaning
  • Handover
  • 00 MAINTENANCE
  • Key-maintenance intervals
  • Reading the fault code memory with the MoDiTeC
  • (Inspections I, II, III and IV)
  • Changing the engine oil [engine only] and oil filter element
  • (Inspection I)
  • Preparatory work
  • Draining engine oil
  • Replacing oil filter element
  • Filling with engine oil
  • Changing the engine oil [engine and oil tank] and oil filter element
  • (Inspections II, III and IV)
  • Preparatory work
  • Draining engine oil
  • Replacing oil filter element
  • Filling with engine oil
  • Cleaning oil strainer in frame
  • (Inspection II, once only)
  • Greasing rubber grommets for cover insert
  • (Inspections I, II, III and IV)
  • Checking coolant, topping up if necessary
  • (Inspections I, II and III)
  • Checking coolant
  • Adding coolant
  • Changing coolant
  • (Inspection IV, every 2 years)
  • Checking and adjusting valve clearances
  • (Inspections II and III)
  • Checking valve clearances
  • Preparatory work
  • Remove the intake air silencer together with the intake air pipe.
  • Exposing the radiator
  • Exposing cylinder head
  • Turning crankshaft-TDC position
  • Checking valve clearance
  • Adjusting valve clearances
  • Installing cylinder head cover
  • Replacing spark plug
  • (Inspection III)
  • Emptying drain from intake air silencer
  • (Inspections I, II and III)
  • Replacing air cleaner element
  • (Inspection III)
  • Replacing fuel filter
  • (Inspection III, every 40,000 km/24,000 miles)
  • Checking clutch play, adjusting if necessary
  • (Inspections I, II and III)
  • Checking brake pads and discs for wear, replacing if necessary
  • (Inspections II and III)
  • Checking brake pads for wear
  • Brake pads, front brake
  • Brake pads, rear brake
  • Replacing brake pads
  • Brake pads, front brake
  • Brake pads, rear brake
  • Checking the brake discs
  • Checking brake fluid level at front and rear
  • (Inspections II and III)
  • Brake fluid level (front brake)
  • Checking brake fluid level (front brake)
  • Brake fluid level (rear brake)
  • Checking brake fluid level (rear brake)
  • Checking operation of brake system and checking for leaks; repairing/ replacing as necessary
  • (Inspection III)
  • Changing brake fluid and bleeding brake system
  • (Inspection IV)
  • Changing brake fluid and bleeding brake system (front brakes)
  • Changing brake fluid and bleeding brake system (rear brakes)
  • Replacing primary sealing boot, front brake master cylinder
  • (Inspection III, every 40,000 km/24,000 miles for motorcycles with ABS)
  • Replacing primary sealing boot, rear brake master cylinder
  • (Inspection III, every 40,000 km/24,000 miles for motorcycles with ABS)
  • Checking toothed belt pulley and sprocket, replacing if necessary
  • (Inspection III)
  • Replacing toothed belt
  • (Inspection III)
  • Checking belt tension, adjusting if necessary
  • (Inspections I, II and III)
  • Checking belt tension
  • Adjusting belt tension
  • Used belt, new belt
  • Checking battery acid level, adding distilled water if necessary
  • (Inspections II, III and IV)
  • Checking battery acid level
  • Adding distilled water
  • Cleaning and greasing battery terminals, if necessary
  • (Inspection IV)
  • Checking and adjusting steering head bearing play, replacing if necessary
  • (Inspections II and III)
  • Checking steering head bearing play
  • Adjusting steering head bearing play
  • Greasing side stand
  • (Inspections II and III)
  • Side stand
  • Checking specified torque of threaded fasteners with torque wrench
  • (Inspections I, II, III and IV)
  • Final inspection with road safety and functional check
  • (Inspections I, II, III and IV)
  • Road safety check
  • Tyre tread depth (recommended minimum value)
  • Tyre pressures (tyres cold)
  • Roadworthiness check
  • 11 ENGINE
  • Technical Data
  • Cutaway view of engine
  • Engine oil circuit
  • Engine and oil-tank system
  • Valve gear
  • Valves, components
  • Oil pumps, components
  • Removing and installing oil pressure switch with engine installed
  • Removing and installing oil pressure switch
  • Cleaning oil tank and oil lines
  • Removing and installing cylinder head, engine installed
  • Preparatory work
  • Removing camshafts
  • Removing cylinder head
  • Removing cylinder, engine installed
  • Removing engine
  • Preparatory work
  • Removing engine
  • Transferring engine-assembly frame
  • Disassembling engine
  • Removing cylinder head
  • Removing camshafts
  • Checking camshaft for wear
  • Removing and installing timing-chain sprockets
  • Checking centrifugal decompressor lever
  • Disassembling and assembling the centrifugal decompressor
  • Removing cylinder head
  • Checking timing chain for wear
  • Disassembling and assembling cylinder head
  • Removing valves
  • Bore for bucket tappet
  • Checking valve guide for wear
  • Removing valve guide
  • Installing valve guide
  • Checking valve seat for wear
  • Installing valve stem seal
  • Checking valve for wear
  • Installing valves
  • Removing cylinder
  • Checking cylinder
  • Removing piston
  • Disassembling piston
  • Determining clearance of piston in cylinder
  • Determining piston ring gaps
  • Determining piston pin clearance
  • Assembling pistons
  • Removing ignition magneto
  • Removing countershaft for starter
  • Disassembling and assembling freewheel
  • Disassembling freewheel
  • Assembling freewheel
  • Removing clutch
  • Removing pressure plate
  • Removing clutch plates
  • Removing and installing oil pump
  • Removing oil pump
  • Inspecting oil pump
  • Installing oil pump
  • Removing double drive gear
  • Removing crankshaft and balancing shaft
  • Checking crankshaft for wear
  • Removing compensating gear
  • Removing and installing crankshaft gear
  • Removing and installing gearbox mainshaft bearings
  • Removing and installing gearbox countershaft bearings
  • Removing and installing grooved ball bearings of balancing shaft
  • Removing and installing main bearings
  • Removal
  • Installation
  • Assembling engine
  • Installing crankshaft and balancing shaft
  • Shimming crankshaft
  • Installing double drive gear
  • Installing oil pump gears
  • Installing clutch
  • Installing clutch cage
  • Installing driver
  • Installing pressure plate
  • Installing countershaft for starter motor
  • Installing magnetic ignition trigger
  • Installing piston
  • Installing cylinder
  • Installing cylinder head
  • Installing camshaft and adjusting valves
  • Installing engine
  • Bleeding engine oil circuit
  • 12 ENGINE ELECTRICS
  • Technical Data
  • Ignition magneto
  • Ignition magneto, components
  • Removing ignition magneto
  • Removing right engine block cover
  • Removing and installing ignition trigger
  • Removing and installing stator
  • Installing ignition magneto
  • Installing magnet rotor
  • Removing and installing, disassembling starter motor
  • Removing and installing starter motor
  • Disassembling and assembling starter motor
  • Replacing spark plug (a 00.42)
  • Removing and installing coil
  • 13 FUEL PREPARATION AND CONTROL
  • Technical Data
  • Removing and installing BMS control unit
  • Removing and installing intake air pipe
  • Removing and installing air temperature sensor
  • Replacing air filter element (a 00.43)
  • Removing and installing intake air silencer
  • Removing and installing intake air pipe
  • Removing and installing injection nozzle
  • Removing and installing throttle-valve actuator
  • Replacing throttle-valve potentiometer
  • Removing and installing throttle flap stub
  • Removing and installing intake stub
  • Checking fuel pressure
  • Removing and installing fuel hoses
  • Removing and installing feed and return lines
  • Removing and installing line-fuel injector
  • Removing and installing throttle cable (a 32.12)
  • 16 FUEL TANK AND LINES
  • Technical Data
  • Removing and installing fuel tank
  • Removing fuel tank
  • Installing fuel tank
  • Removing and installing fuel filler cap
  • Removing and installing roll- over valve
  • Replacing fuel filter (a 00.44)
  • Removing and installing fuel pump
  • Removing and installing fuel- evaporation control valve
  • [USA version]
  • Removing and installing activated charcoal filter
  • [USA version]
  • 17 RADIATOR
  • Technical Data
  • Coolant circuit
  • Thermostat, components
  • Removing and installing coolant pump
  • Removing coolant pump
  • Installing coolant pump
  • Adding coolant
  • Removing and installing coolant-temperature sensor
  • Checking cooling system for leaks
  • Removing and installing coolant hoses
  • Replacing coolant hose (cylinder head/frame - frame/radiator)
  • Replacing coolant hose (radiator/water pump)
  • Replacing coolant hose (filler bowl/expansion tank)
  • Changing coolant (a 00.36)
  • Removing and installing fan
  • Removing and installing radiator
  • Removing and installing thermostat
  • 18 EXHAUST SYSTEM
  • Technical Data
  • Removing and installing exhaust system
  • Removing and installing silencer (muffler)
  • Removing and installing exhaust elbow and oxygen sensor
  • Removing exhaust elbow and oxygen sensor
  • Installing exhaust elbow and oxygen sensor
  • Replacing guard for silencer
  • 21 CLUTCH
  • Technical Data
  • Clutch, components
  • Removing and installing clutch
  • Removing clutch
  • Removing pressure plate
  • Disassembling and reassembling pressure plate
  • Removing clutch plates, driver and clutch cage
  • Installing clutch cage
  • Installing driver
  • Installing pressure plate
  • Check clutch discs for wear
  • Removing and installing release shaft
  • Installing clutch
  • 23 GEARBOX
  • Technical Data
  • Gearbox shafts, components
  • Gear shift pedal, components
  • Replacing shaft sealing rings with engine installed
  • Replacing sealing ring of selector shaft
  • Replacing shaft sealing ring of belt sprocket
  • Removing and installing gearbox
  • Removing selector shaft with pawl and index lever
  • Removing selector forks
  • Removing selector drum
  • Removing, disassembling and reassembling gearbox shafts
  • Removing gearbox shafts
  • Disassembling and reassembling mainshaft
  • Checking mainshaft for wear
  • Disassembling and reassembling countershaft
  • Checking countershaft for wear
  • Replacing gearbox mainshaft bearings
  • Replacing gearbox countershaft bearings
  • Installing gearbox shafts
  • Installing selector shaft
  • Installing selector forks
  • Installing selector drum
  • 27 CHAIN/BELT DRIVE
  • Technical Data
  • Removing and installing belt, belt drive gear and belt sprocket
  • Removing and installing belt (a 00.54)
  • Removing and installing belt sprocket (a 33.13)
  • Removing and installing belt sprocket
  • Adjust belt tension (a 00.56).
  • 31 FRONT FORKS
  • Technical Data
  • Telescopic fork, components
  • Removing and installing telescopic fork
  • Removing telescopic fork
  • Installing telescopic fork
  • Disassembling telescopic fork
  • Removing fixed tube
  • Measuring telescopic fork
  • Checking lower fork bridge
  • Checking parallel alignment of fixed tubes
  • Checking fixed tube runout
  • Assembling telescopic fork
  • Assembling fixed tube
  • Complete assembly of telescopic fork.
  • Removing and installing steering head bearing
  • Upper steering head bearing
  • Lower steering head bearing
  • 32 STEERING
  • Technical Data
  • Removing and installing left and right handlebar fittings
  • Removing and installing left handlebar fitting
  • Removing and installing clutch switch
  • Removing and installing right handlebar fitting
  • Removing and installing handlebar
  • Removing and installing clutch cable
  • Removing and installing throttle cable
  • Removing and installing left and right handlebar levers
  • Removing and installing left handlebar lever
  • Removing and installing right handlebar lever
  • Checking and adjusting steering head bearing play, replacing if necessary (a 00.60)
  • 33 REAR WHEEL DRIVE
  • Technical Data
  • Removing and installing suspension strut
  • Removing and installing rear swinging arm
  • Removing and installing needle roller races in rear swinging arm
  • Removing needle roller races
  • Installing needle roller races
  • Removing and installing needle bearings in rear swinging arm
  • Removing needle roller bearing
  • Installing needle roller bearing
  • Removing and installing reaction link
  • Removing and installing angled lever
  • Removing and installing needle roller bearings and needle roller races in angled lever
  • Removing needle roller bearings and needle roller races
  • Installing needle roller bearings and needle roller races
  • Removing and installing drive damper
  • Removing drive damper
  • Removing pulley
  • Disassembling drive damper
  • Assembling drive damper
  • Installing pulley
  • Installing drive damper
  • Measuring runout of belt pulley
  • Removing and installing eccentric with drive shaft
  • Separating eccentric from drive shaft
  • Removing and installing floating bearing of eccentric
  • Removing and installing fixed bearing of eccentric
  • Pressing eccentric onto drive shaft
  • 34 BRAKES
  • Technical Data
  • Removing and installing front brake caliper
  • Removing and installing front brake pads (a 00.46)
  • Removing and installing front brake pistons
  • Removing and installing front brake disc
  • Checking brake disc for wear (a 00.45)
  • Checking front brake disc for lateral runout
  • Removing and installing rear brake caliper
  • Removing and installing rear brake pads (a 00.46)
  • Removing and installing rear brake pistons
  • Removing and installing rear brake disc
  • Checking brake disc for wear (a 00.47)
  • Checking rear brake disc for lateral runout
  • Replacing primary sealing boot, front brake master cylinder (a 00.52)
  • Removing and installing front brake master cylinder
  • Removing and installing handbrake lever (a 32.13)
  • Replacing primary sealing boot, rear brake master cylinder (a 00.53)
  • Removing and installing rear brake master cylinder
  • Removing and installing brake pedal
  • Checking blow-by clearance at piston thrust rod, adjusting if necessary
  • Checking blow-by clearance at piston rod
  • Adjusting play at piston rod
  • Removing and installing front ABS sensor
  • Removing and installing front ABS sensor ring
  • Removing and installing rear ABS sensor
  • Removing and installing ABS control unit
  • Removing and installing front brake lines/hoses (with ABS)
  • Removing and installing brake lines
  • Removing and installing front brake hoses
  • Removing and installing rear brake lines/hoses (with ABS)
  • Removing and installing brake lines
  • Removing and installing brake hose
  • Checking front ABS sensor ring for runout
  • 36 WHEELS AND TYRES
  • Technical Data
  • Removing and installing front wheel
  • Removing front wheel
  • Installing front wheel
  • Removing and installing front wheel bearing
  • Removing left-hand wheel bearing
  • Removing right-hand wheel bearing
  • Installing wheel bearings
  • Removing and installing rear wheel
  • Checking front and rear wheel rims
  • Checking rims
  • Static balancing of front/rear wheel
  • 46 FRAME
  • Technical Data
  • Overview of trim panels
  • Removing and installing trim panels
  • Removing and installing left and right covers
  • Removing and installing rear cover
  • Removing and installing front cover
  • Removing and installing left and right covers
  • Removing and installing windscreen and windscreen holder
  • Removing and installing headlight surround
  • Removing and installing instrument cover
  • Removing and installing left/right connector covers
  • Removing and installing left connector cover
  • Removing and installing right connector cover
  • Removing and installing fairing bracket
  • Removing and installing front mudguard
  • Removing and installing rear mudguard
  • Removing and installing number- plate carrier
  • Removing and installing spray guard
  • Removing and installing number-plate carrier
  • Removing and installing left/right rear trim panel
  • Removing and installing luggage rack
  • Removing and installing stowage- compartment frame
  • Removing and installing oil-tank trim panels
  • Raising, removing and installing rear frame
  • Raising rear frame
  • Removing and installing rear frame
  • Removing frame
  • Removing and installing left and right footrests
  • Removing and installing rear footrest
  • Removing and installing side stand truss
  • Removing and installing side stand
  • Measuring wheel track offset
  • Measurement record, wheel track offset
  • Key-measurement result:
  • Checking frame with gauge
  • Front wheel
  • Rear wheel
  • Example
  • 51 EQUIPMENT
  • Technical Data
  • Removing and installing ignition switch/steering lock
  • Removing and installing lock barrel
  • Removing and installing lock for rear stowage compartment
  • Removing and installing lock barrel for fuel tank filler cap
  • Replacing mirrors
  • 61 GENERAL ELECTRICAL EQUIPMENT
  • Technical Data
  • Wiring harness
  • View from left
  • View from right
  • Component positions in electronic equipment box
  • Relay positions in electronic equipment box
  • Connectors, electronics box
  • Removing and installing battery (a 00.20)
  • Removing and installing battery carrier (a 34.17)
  • Replacing fuses
  • Motorcycle fuses
  • Fuses
  • Removing and installing holder for BMS control unit
  • Removing and installing coolant-temperature sensor (a 17.10)
  • Removing and installing side stand switch
  • Removing and installing rear-brake switch for brake light
  • Removing and installing front-brake switch for brake light
  • Removing and installing horn
  • Removing and installing neutral-indicator switch
  • Removing and installing front/rear ABS sensors (a 34.15)/(a 34.16)
  • Removing and installing voltage regulator
  • Removing and installing switch for hazard warning flashers
  • 62 INSTRUMENTS
  • Technical Data
  • Telltale/warning lights
  • Removing and installing instrument panel
  • Replacing telltale/warning lights
  • Disassembling and assembling instrument cluster
  • Removing and installing wiring harness
  • 63 LIGHTS
  • Technical Data
  • Removing and installing headlight
  • Removing and installing rear light
  • Removing and installing number- plate light
  • Replacing bulbs
  • Bulb for low-beam headlight/ high-beam headlight
  • Bulb, parking light
  • Flashing turn indicator
  • Rear lights
  • Bulb for number-plate light
  • Checking and adjusting headlight beam throw
  • Vertical adjustment
  • Lateral adjustment