• -$10.00
BMW R 850 1200 C - Service Manual - Repair Manual
search
  • BMW R 850 1200 C - Service Manual - Repair Manual

BMW R 850 1200 C - Service Manual - Repair Manual

$29.95
$19.95 Save $10.00
No tax
Quantity

YOUTUBE Official Channel @SoloPDFcom (+18,000 subs). Trusted by mechanics worldwide using professional workshop manuals and wiring diagrams.

BMW R 850 1200 C - Service Manual - Repair Manual

Digital technical documentation with sections on MAINTENANCE SCHEDULE, PRE-DELIVERY CHECK, MAINTENANCE AND GENERAL INSTRUCTIONS. Review the complete contents below for the systems and procedures covered.

Manual contents

  • INTRODUCTION
  • MAINTENANCE SCHEDULE
  • PRE-DELIVERY CHECK
  • 00 MAINTENANCE AND GENERAL INSTRUCTIONS
  • Tightening torques
  • Table of operating fluids
  • Key-maintenance intervals
  • Reading out MoDiTeC fault memory
  • (Inspections I, II, III and IV)
  • Checking throttle cable play, adjusting if necessa...
  • (Inspections I and III)
  • Changing engine oil, renew oil filter element
  • (Inspections I, II, III and IV)
  • Changing oil in gearbox
  • (Inspections III and IV)
  • or at least every 2 years
  • Changing oil in rear wheel drive; cleaning inducti...
  • (Inspections I, III and IV)
  • Every 40 000 km (24 000 miles) or at least every 2...
  • Renewing fuel filter
  • (Inspection III)
  • In normal operating conditions every 40 000 km (24...
  • Checking battery acid level/topping up if necessar...
  • (Inspections III and IV)
  • Renewing intake air cleaner element
  • (Inspection III)
  • In very dirty and dusty operating conditions, rene...
  • Renewing Poly-V belt
  • (every 60 000 km/36 000 miles)
  • (Inspection III)
  • Poly-V belt adjusting procedure:
  • Checking brake fluid level
  • Front brake
  • Rear brake
  • Checking brake pads and discs for wear/renewing
  • (Inspections II and III)
  • Checking front brake pad wear
  • Checking rear brake pad wear
  • Checking brake disc wear
  • Renewing brake pads Front brake
  • Renewing brake pads Rear brake
  • Renewing brake fluid and bleeding brake system
  • Renew the brake fluid annually
  • (Inspection IV)
  • [ABS Inspection II and III]
  • Bleeding front brake circuit/renewing brake fluid
  • Additionally with [ABS]
  • Bleeding rear brake circuit/renewing brake fluid
  • Additionally with [ABS]
  • Checking clutch operating fluid level
  • (Inspections I, II and III)
  • Checking tightness of rear wheel studs
  • (Inspection I)
  • Checking rear wheel bearing play by tilting wheel
  • (Inspection III)
  • Checking swinging arm bearings, adjusting if neces...
  • (Inspections I and III)
  • Greasing the side (prop) stand pivot
  • (Inspections I, II and III)
  • Checking function of side (prop) stand contact swi...
  • (Inspections I, II, III and IV)
  • Tightening cylinder heads
  • (Inspection I)
  • Checking/adjusting valve operating clearances
  • (Inspections I, II and III)
  • Checking/renewing spark plugs
  • (Inspection II)/renewing (Inspection III)
  • Check synchronising
  • (Inspections I, II and III)
  • Final inspection with road safety and functional c...
  • (Inspections I, II, III and IV)
  • Road safety check
  • Roadworthiness check
  • 11 MOTOR
  • Sectioned drawing of engine
  • Lubricating oil circuit
  • Coolant circuit
  • Removing engine
  • Dismantling engine
  • Removing cylinder head cover
  • Locking the engine in the TDC position
  • Top dead centre on ignition stroke:
  • Removing and installing chain tensioner
  • Assembly specification for timing chain tensioner:...
  • Removing valve gear holder
  • Dismantling/reassembling valve gear holder
  • Removing cylinder head
  • Dismantling, checking, repairing and re-assembling...
  • Removing and installing valves
  • Removing valve stem seals
  • Checking valves for wear
  • Remachining valve seat
  • Checking and repairing cylinder head
  • Checking valve guide for wear
  • Replacing valve guides
  • Installing valve and valve stem seal
  • Removing cylinder barrel
  • Removing/dismantling piston
  • Checking pistons and cylinders
  • Assembling pistons
  • Removing/installing conrod
  • Removing and installing alternator cover with engi...
  • Removing alternator mount cover
  • Renewing radial shaft seal in alternator mount cov...
  • Renewing radial shaft seal for rotary breather
  • Removing auxiliary shaft drive
  • Removing oil pump
  • Removing radial shaft seal on crankshaft with engi...
  • Dismantling crankcase
  • Removing crankshaft, auxiliary shaft and timing ch...
  • Removing and installing oil pick-up basket
  • Replacing oil level sight glass
  • Removing conrods
  • Checking conrods
  • Measuring main and big end bearing play
  • Measuring radial bearing play
  • Installing main bearing
  • Measuring axial bearing play
  • Measuring big end bearing play
  • Assembling engine
  • Installing conrod
  • Installing crankshaft
  • Installing timing chain tensioning and slide rails...
  • Installing auxiliary shaft/timing chains
  • Assembling engine block
  • Installing the crankshaft radial seal
  • Installing clutch housing
  • Installing oil pump
  • Installing auxiliary shaft drive
  • Installing piston
  • Installing cylinder
  • Installing cylinder head
  • Adjusting valve clearances
  • Installing right cylinder head
  • Adjustment specification
  • Installing left cylinder head
  • Adjustment specification
  • Installing alternator mount cover
  • Installing magnetic gate/belt pulley
  • Timing the ignition
  • Installing alternator
  • Installing engine
  • 12 ENGINE ELECTRICS
  • Removing and installing coil and ignition lead
  • Check ignition coil resistance
  • Removing and installing alternator
  • Poly-V belt adjusting procedure:
  • Dismantling/reassembling alternator
  • Checking alternator
  • Checking armature for short-ground (earth)
  • Removing and installing starter motor
  • Dismantling/reassembling starter motor
  • Renewing carbon brushes
  • Checking starter motor
  • Checking starter relay
  • Removing and installing magnetic gate
  • Timing the ignition
  • 13 FUEL PREPARATION AND CONTROL
  • Removing and installing air cleaner
  • Removing and installing throttle stub pipe
  • Removing and installing throttle potentiometer
  • Removing and installing throttle positioner
  • Removing and installing throttle potentiometer
  • Removing and installing injectors
  • Removing and installing Motronic control unit
  • 16 FUEL TANK AND LINES
  • Removing and installing fuel tank
  • Removing and installing fuel filter, fuel pump and...
  • Removing and installing fuel filter
  • Removing and installing fuel pump and fuel level s...
  • Checking fuel pump pressure
  • Removing and installing fuel distributor and press...
  • 18 EXHAUST SYSTEM
  • Removing and installing exhaust system
  • Removing and installing silencer (muffler)
  • Removing and installing front exhaust pipes
  • 21 CLUTCH
  • Removing and installing clutch hydraulic line
  • Removing and installing clutch slave cylinder
  • Filling/bleeding clutch line
  • Removing and installing clutch
  • Removing clutch
  • Installing clutch
  • 23 GEARBOX
  • Removing and installing gear pedal
  • Removing gearbox
  • Renewing the shaft sealing rings in the gearbox ho...
  • Renew the input shaft sealing ring at the input en...
  • Renewing output shaft sealing ring
  • Renewing input shaft sealing ring at output side
  • Renewing shaft sealing ring for selector drum
  • Renewing sealing ring for selector shaft
  • Dismantling gearbox
  • Removing gearbox housing
  • Removing selector drum
  • Dismantling/assembling selector shaft
  • Removing gearbox shafts
  • Renewing deep-groove ball bearing on intermediate ...
  • Dismantling/assembling input shaft
  • Dismantling input shaft
  • Assembling input shaft
  • Dismantling/reassembling output shaft
  • Stripping down output shaft
  • Assembling output shaft
  • Checking endplay
  • Checking/adjusting fully compressed length of gear...
  • Checking/adjusting fully-compressed length of inte...
  • Checking/adjusting fully-compressed length of outp...
  • Checking/adjusting fully-compressed length of inpu...
  • Checking/adjusting fully-compressed length of sele...
  • Shimming selector shaft
  • Assembling gearbox
  • Installing input, output and intermediate shaft
  • Installing selector shaft
  • Installing selector drum
  • Assembling gearbox housing
  • 31 FRONT FORK
  • Removing and installing telescopic fork
  • Removing and installing telescopic fork
  • Removing and installing fork bridge
  • Removing and installing pot-type joints
  • Removing and installing ball thrust bearing
  • Removing and installing slider tube bridge
  • Removing and installing ball joint
  • Checking friction at ball joint/ball thrust bearin...
  • Assembly specification for telescopic fork:
  • Dismantling/reassembling telescopic fork
  • Dismantling telescopic fork
  • Assembling telescopic fork
  • Measuring telescopic fork
  • Check slider tube bridge
  • Checking runout of fixed tube
  • Removing and installing leading link
  • Dismantling/reassembling leading link
  • Removing and installing front suspension strut
  • 32 STEERING
  • Removing and installing left handlebar fitting
  • Removing and installing right handlebar fitting
  • Removing and installing handlebar
  • Removing/installing throttle cable
  • 33 REAR WHEEL DRIVE
  • Removing, dismantling, reassembling and installing...
  • Removing rear wheel drive
  • Removing input bevel pinion
  • Disassembling input bevel pinion
  • Removing needle roller bearing for input bevel pin...
  • Installing needle roller bearing for input bevel p...
  • Assembling input bevel pinion
  • Installing input bevel pinion
  • Removing and dismantling the crown wheel
  • Assembling/installing crown wheel
  • Checking/adjusting backlash
  • Checking tooth contact pattern
  • Shimming housing cover
  • Installing housing cover
  • Installing splined element
  • Removing/installing rear swinging fork
  • Removing rear swinging arm
  • Removing and installing taper roller bearing
  • Removing and installing flexible gaiter
  • Removing drive shaft
  • Checking universal joint for wear
  • Installing drive shaft
  • Installing rear swinging arm
  • Installing rear wheel drive
  • Removing and installing suspension strut
  • 34 BRAKES
  • Removing and installing front brake caliper
  • Dismantling and assembling front brake caliper
  • Dismantling front brake caliper
  • Assembling front brake caliper
  • Removing and installing rear brake caliper
  • Dismantling and assembling rear brake caliper
  • Dismantling rear brake caliper
  • Assembling rear brake caliper
  • Removing and installing front brake disc
  • Removing/installing rear brake disc
  • Removing and installing front ABS sensor
  • Adjusting front ABS sensor gap
  • Marking sensor wheel
  • Checking and adjusting sensor gap
  • Removing and installing rear ABS sensor
  • Adjusting rear ABS sensor gap
  • Marking sensor wheel
  • Checking and adjusting sensor gap
  • Removing and installing rear brake master cylinder...
  • Checking and adjusting relief clearance of piston ...
  • Removing and installing brake pedal
  • Removing and installing ABS unit
  • Removing the ABS unit
  • Installing the ABS unit
  • Removing and installing ABS relay and relay base
  • Removing ABS relay
  • Installing the ABS relay
  • Removing ABS relay base
  • Installing the ABS relay base
  • Removing and installing brake lines
  • Removing and installing front brake line
  • Removing and installing rear brake line
  • 36 WHEELS AND TYRES
  • Removing and installing front wheel
  • Removing front wheel
  • Installing front wheel
  • Removing and installing wheel bearings
  • Removing/installing rear wheel
  • Static balancing of front wheel/rear wheel
  • Checking front/rear wheel rim for runout
  • Removing/installing spokes
  • Centering the wheel rim
  • Centering lateral runout
  • 46 FRAME
  • Removing and installing rear mudguard
  • Removing/installing front mudguard
  • Removing and installing front frame
  • Removing and installing rear frame
  • Removing/installing footrest supports
  • Removing and installing side (prop) stand
  • Checking running gear
  • Measuring wheel track offset
  • 51 EQUIPMENT
  • Removing and installing ignition switch/steering l...
  • Removing and installing ignition/light switch
  • Removing and installing lock barrel
  • Drilling out lock barrel
  • Removing and installing lock barrel for fuel tank ...
  • Drilling out lock barrel
  • 52 SEAT
  • Removing and installing seat
  • 61 GENERAL ELECTRICAL EQUIPMENT
  • Removing and installing central electrical equipme...
  • Relay positions (central electrical equipment box)...
  • Connections-fuses:
  • Frame wiring harness
  • Wiring harness View from left
  • Wiring harness View from right
  • 62 INSTRUMENTS
  • Removing and installing instrument cluster
  • Dismantling and assembling instrument cluster
  • 63 LIGHTS
  • Removing and installing headlight
  • Adjusting headlight